Gemini PS-626i Operation Manual

Also see for PS-626i: Operation manual

Contents

specifications

Page 5SPECIFICATIONSINPUTS:DJ Mic.......................................................1.5mV 2 kΩ unbalancedPhono @ 1 kHz..........................................................................2 mV 47 kΩLine...............................................................................100 mV 27 kΩOUTPUTS:Amp/Booth....................................................................0 dB 775mV 400 ΩMax...............................................................................24V Peak-to-PeakRec..................................................................................225mV 5 kΩGENERAL:Bass .....................................................................+ 12dB/- 32 dBMid ..........................................................................+ 12dB/- 32 dBTreble ..................................................................+ 12dB/- 32 dBGain (Mic).......................................................................0 to -40dBGain (Chnls 1-3).......................................................................0 to -20dBFrequency Response............................................20Hz - 20kHz +/- 2dBDistortion..............................................................................less than 0.02%S/N Ratio..........................................................................better than 80dBTalkover Attenuation........................................................................16dBPower Source...................................................115/230V 50/60Hz 20WDimensions................................................254mmW x 305mmD x 112mmH10”W x 12”D x 4 7/16”HWeight........................................................................................6.5 lbs(3 Kg)F Your Gemini mixer comes with an RG-45 PRO (RAILGLIDEô) DUAL-RAIL CROSSFADER. Rail Glide™Crossfaders have internal dual stainless steel rails that allow theslider to ride smoothly and accurately from end to end.4. CROSSFADER SECTION: The CROSSFADER (25) allows the mixingof one source into another. The left side of the CROSSFADER (25) ischannel 2 and the right side is channel 3.5. BEAT INDICATORS: Each side of the CROSSFADER (25) has its ownBEAT INDICATOR (23, 24). They flash at the low frequency peaklevel allowing you to match the beats visually. BEAT INDICATOR (23)will reflect the beat of CH2 and BEAT INDICATOR (24) will do thesame for CH3.6. OUTPUT CONTROL SECTION: The level of the AMP OUT (38) iscontrolled by the MASTER (18) control. The BALANCE (17) controlwill allow the Amp Out signal to be balanced between the left andright speakers. The BOOTH (16) control adjusts the level of theBOOTH OUTPUT (39).HINT: BOOTH OUTPUT (39) is used by some DJs to run monitorspeakers in the DJ Booth. You can also use it as a secondZONE or AMP output.NOTE: The RECORD OUT (40) has no level control. The level isset by the channel slides and the gain controls of the selectedchannel. Tonal qualities are set by the low, mid and highcontrols of that same channel.7. TALKOVER SECTION: The purpose of the talkover section is to allowthe program playing to be muted so that the mic can be heard abovethe music. When the TALKOVER (19) button is pushed, theTALKOVER INDICATOR (28) will glow and the volume of all sourcesexcept the Mic or whatever is connected to the PHONO/LINE (36)input are reduced by 16 dB.8. CUE SECTION: By connecting a set of headphones to theHEADPHONE (4) jack, you can monitor any or all of the channels.Select the correct CUE (21) button or buttons and their respectiveCUE LED (5) indicators will glow. Use the CUE LEVEL (20) control toadjust the headphone volume without effecting the overall mix. Bysliding the CUE PGM PAN (22) control to the left you will be able tomonitor the assigned cue signal. Sliding to the right will monitor thePGM (program) output.9. DISPLAY: The peak hold, dual function DISPLAY (26) indicates eitherthe MASTER (38) output left and right levels or the channel 2 andchannel 3 levels. You can choose the option you want by pressingthe DISPLAY (27) button.NOTE: When the DISPLAY (27) is in the channel 2/channel3 display mode, by adjusting the individual channel gainand tone controls, you can increase or decrease thesignal to match the other channel’s signal. The channelslides and crossfader have no effect on the displayreadings.10. The CROSSFADER CURVE SWITCH (31) allows you to adjust thekind of curve the crossfader has. Move switch to the “sharp” positionto make the curve steep and cutting (perfect for scratching ). Moveswitch to the “gradual” position to make the curve gradual and gentle.The CROSSFADER REVERSE SWITCH (32) allows you to reverse thecrossfader so that CHANNEL 3 is controlled by the left side of thecrossfader and CHANNEL 2 is controlled by the right side of thecrossfader.NOTE: When the CROSSFADER REVERSE SWITCH (32) isactivated, only the crossfader reverses. The ChannelSlides, Gain, and Tonal Controls do not reverse.

/ 6

Related manuals for Gemini PS-626i