Genie 2020L Series Operation And Maintenance Manual

Also see for 2020L Series: Operation and maintenance manual

Contents

Genie 2020L Series Operation And Maintenance Manual Manual pdf 8 page image

8 For Help, call 1-800-35-GENIE or visit www.geniecompany.comCh pRoGRammiNG theR emote C oNtRolProgramming 1:A To program one Button of a Remote Control (Figure 11):• Locate Learn Button and Learn Indicator Light nearTerminal Block on Power Head (Figure 12)• Press and release Learn Button Red Learn Indicator Lightwill blink 2 times per second• Press Remote Control Button once within 30 seconds RedLearn Indicator Light will stay lit• Press Remote Control Button again Red Learn IndicatorLight will go out, indicating that memory is stored• Press again to Activate UnitB Program each additional Remote using step A aboveaCCeSSoRieSRemote Control OperationA Press Button on Remote Control Garage door will moveB Press Button again Garage door will stop:• The door automatically stops at the end of theopen or close cycleC Press Button again Garage door will reverseWARNINGA moving garage door may cause serious injury or death• Keep people clear of opening while door is moving• Do not allow children to play with the Remote ControlsIf the Safety Reverse does not work properly:• Close the door and disconnect the Opener using theEmergency Release Cord• Do not use the door Opener, Remote Controls, orWireless Keypad• Refer to the door and door Opener Owner’s Manualsbefore attempting any repairsFigure 12 Learn Code Button and Indicator Light(Located Lower Right Corner)OPENCLOSELEARNCODEBUTTONLEARNINDICATORLIGHTFigure 111-Button and 3-ButtonCompact Remotesw/Docking StationD There are several additional varieties of remote controlsavailable from your local dealer, some equipped witha flashlightA Open garage door using Wall ConsoleB Lay a 2” x 4” board flat in center of doorway (Figure 10)C Close door using Wall ConsoleD Check that door stops and reverses within 2 seconds after itcontacts board:• If door does not reverse, decrease Close Force untildoor reverses (Figure 9)• If door still does not reverse, move Limit Switchtoward doorE Check Safe-T-Beam® System operation:• If beam is blocked, doorwill not closeNOTEThe door must contact the 2” x 4” board before theCarriage activates the Close Limit Switch If not,readjust the Close Limit SwitchCh S ettiNG C oNtaCtR eVeRSe fuNCtioNaDjuStmeNt 2:NOTELimit Switch and Force Adjustments must be completed beforechecking the contact reverse function2” x 4” boardlaid flatFigure 10CheckingContactReverseNOTE• Each Remote Control must be programmedseparately• The Remote Controls will not close the garage withmalfunctioning Safe-T-Beam® System• Program Remote Controls, while at least 24” fromAntenna Wire• If the red Learn Indicator Light blinks rapidly,programming stopped Restart programming• Each Button on a multi-button Remote Control isfor a different Opener Cannot use more than oneButton for same Opener• A maximum of seven Remote Controls or WirelessKeypads can be stored into the Receiver at onetime If a Remote Control becomes lost, or if youwant to delete a Remote Control or WirelessKeypad, see “To Erase All Receiver Memory ”To Erase All Remotes from Power Head MemoryA Press and hold Learn Button on Power Head for 10 secondsor until Learn Indicator Light goes out Memory is erased:• Program Remotes again as neededTo Replace Remote Control BatteryA FOR NON-FLASHLIGHT MODELS• Pop off the back of the transmitter– Use coin, pen, screwdriver or any similar device– Replace old Battery with new coin type battery• Replace back of remote.B FOR FLASHLIGHT MODELS• Slide open battery cover– Replace old Battery with new AAA battery• Replace battery cover.