Genie G3T-BX Programming Instructions Manual
Contents |
3 Button RemoteProgramming InstructionsWARNINGMoving Door can cause serious injuryor death.• Wall Console must be mounted in sightof door, at least 5 feet above floor andclear of moving door parts.• Keep people clear of opening while door is moving.• Do NOT allow children to play with the Remote ordoor opener.If safety reverse does not work properly:• Close door then disconnect opener using themanual release handle.• Do NOT use Remote or door opener.• Refer to Door and Door Opener Owner’s Manualsbefore attempting any repairs.1 Putting Opener into Programming ModeRADIOSIGNALLEARNCODE CODELEARNSETSETOPENFORCECLOSECODELEARN LIMITMANUALorNew Genie® OpenersGenie® Openers and External Receivers Manufactured between 1995 to 2011PULLRADIOSIGNALLEARNCODERADIOSIGNALLEARNCODE-OR-NOTE: Once in programming mode, you will haveapproximately 30 seconds to perform this step.©2014 GMI Holdings, Inc. DBA The Genie CompanyFCC and IC CERTIFIEDThis device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to thefollowing two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occur in a particular situation. If thisequipment does cause harmful interference to radio or television reception, which may be determined by turning theequipment OFF and ON, the user is encouraged to try and correct the interference by one or more of the followingmeasures: (a) Re-orient or relocate the receiver antenna, (b) Increase the separation between the opener and receiver,could void the users authority to operate the equipment.1. Press and hold theprogram button untilthe round LED turnsblue, then release.2 Programming a Remote to your OpenerLost or Stolen Remote/Erasing all Remotes3Battery Replacement4NOTE: For openersmanufactured between1995-1999,use the two upperbuttons on the remoteReplace remote battery with CR2032 coin cell battery.1. Open the remote case using a washer orcoin that fits into the slot at the top of theremote.2. Replace battery. Match battery polaritysymbols inside battery housing.3. Align components and snap case closed.For additional information or helpcontact customer service:Call 1-800-35-Genie or write:GMI Holdings INC.d/b/a The Genie Company1 Door DriveMount Hope Ohio 44660New Genie® OpenersPROGRAMSET – +38382502359 02/2014PROGRAMSET – +PROGRAMSET – +PROGRAMSET – +PROGRAMSET – +2. The round LED willgo out and the longLED will begin flash-ing purple.Proceed to step 2.1. Pull protective battery tab from remote.PROGRAMSET – +PROGRAMSET – +PROGRAMSET – +PROGRAMSET – +1. Press and hold theprogram button until theround LED turns blue,then release.2. Press and hold the Up(+) Down (-) buttons atthe same time, until the both LEDs flash blueand go OFF.• To erase all remote devices from all other types of Genie® openers,Press and hold the Learn Code Button until the LED stops blinking.Start at step 1 to reprogram your remotes.NOTE: Clearing remote control memory from the power head will clear ALL pro-grammed remotes and keypads. Your opener will no longer recognize any signalfrom any remote device, including a missing remote device.Genie® Openers and External Receivers Manufactured between 1995 to 20111. Press & Release Learn Code button once. The red LED will begin toflash.Proceed to step 2.Note: While programing remote buttons, standat least 5 feet away from the opener. This ensuresyou have proper communication between theremote and the opener.2. Slowly press and release the remote buttonof your choice two times. The opener LEDs willflash and go off, indicating you have successfullyprogrammed your remote.3. Press and release the same button a third time and door will open orclose. It is possible to press the remote button too quickly or lightly. Ifthe LEDs do not go OFF, press the remote button several more times toachieve confirmation.NOTE: For openersmanufactured between1995-1997,use the two upperbuttons on the remote.Made after 1997? Use anybutton for programming.For more information, please visit www.devancocanada.com or call toll free at 855-931-3334 |
Related manuals for Genie G3T-BX
Genie G3T-R Programming Instructions Manual
Genie GT912-BX Instructions Manual
Genie ACSCTG-UNIV2 Instructions Manual
Genie INTELLICODE GITR-3BX Instructions Manual
Genie UNIVERSAL REMOTE Instructions Manual
Genie 3 Button Remote Operating Instructions Manual
Genie Series III Installation Instructions Manual
Genie Remote Control Operating Instructions Manual
Genie QN-RS283 Instruction Manual And Parts Listing
Genie Confirm Installation And Operation Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine