Genie GK-R Instructionsfor Use
38832503793Wireless Keypad InstructionsIt is recommended to complete programming before mounting keypadKeypadUp/Down Key(enter)Program KeyLEDLED OffLED OnLED FlashingKeypad Off Keypad On Keypad FlashingKeypad LED’s Successful Entries Failed EntriesSAVE THESEINSTRUCTIONSFOR FUTUREUSEWARNING!MOVING DOOR CAN CAUSE SERIOUSINJURY OR DEATH.• DO NOT install transmitter (keypad) unless the door operator’ssafety device works as required by the door operator’s manual.• Wall Console must be mounted in sight of door, at least 5 feetabove floor and clear of moving door parts.• Keep people clear of opening while door is moving.• DO NOT allow children to play with the transmitter or dooroperator.If safety reverse does not work properly:• Close door then disconnect opener using the manual releasehandle.• DO NOT use transmitter or door operator.• Refer to Door and Door Opener Owner’s Manuals beforeattempting any repairs.AVERTISSEMENT!DÉMÉNAGEMENT PORTE PEUT CAUSER DESBLESSURES GRAVES OU LA MORT.• NE PAS installer le transmetteur (clavier) à moins que le dispositifde sécurité de l’opérateur de porte ne fonctionne comme l’exige lemanuel d’utilisation de la porte.• Console murale doit être monté en vue de la porte d’au moins 5pieds au-dessus-de-chaussée et claire des pièces mobiles de laporte.• Garder les personnes clair de l’ouverture lorsque la porte est enmouvement.• Ne pas laisser les enfants jouer le premier match à distance ou laporte.Si la sécurité inverse ne fonctionne pas correctement:• Fermer la porte, puis débranchez moteur à l’aide de la poignée dedéverrouillage manuel.• Ne pas utiliser d’ouverture à distance ou la porte.• Reportez-vous à la porte et ouvre-porte de propriétaires manuelsavant de tenter toute réparation.Keypad LED will flash each timea key is pressed and entry isaccepted.Keypad LED and PROGRAM keywill flash slowly and number padback light will remain on for 15seconds indicating a successfulprogram or valid PIN has beenentered.Keypad LED, PROGRAM key andnumber pad back light will flashrapidly indicating a problem withprogramming or an invalid PIN entry.• Wait 15 seconds until back lightingshuts off and enter a valid PIN orreset keypad to reprogram.FCC Part 15.21 Statement:Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority to operatethe equipment.FCC / IC Statement:This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, includinginterference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canadaapplicables aux appareils radio exempts de licence. L’exploitation estautorisée aux deux conditions suivantes : (1) l’appareil ne doit pasproduire de brouillage, et (2) l’utilisateur de l’appareil doit acceptertout brouillage radioélectrique subi, même si le brouillage estsusceptible d’en compromettre le fonctionnement.Single Door Operation:1. Ensure number pad back lighting is off.2. Enter PIN.3. Press the UP/DOWN key.4. Opener will operate.Multi-Door Operation:1. Ensure number pad back lighting is off.2. Enter PIN.3. Press the UP/DOWN key.4. Press number key corresponding with desired door(1, 2, or 3).5. Desired opener will operate.Changing an Existing PIN:1. Enter current PIN2. Press PROGRAM key once.3. Enter new PIN (3-8 digits)4. Press PROGRAM key once.• Your PIN has been changed and your previous PIN will nolonger operate keypad or opener.ADDITIONAL (OPTIONAL) PROGRAMMING:Setting a Temporary PIN:A temporary PIN allows temporary access to the garageby normally unauthorized personnel such as repairmen orneighbor.1. Enter current PIN.2. Press PROGRAM key 3 times.3. Enter a temporary PIN (3 to 8 digits)4. Press PROGRAM key once.• The Temporary PIN will operate garage door opener untilthe original PIN is used. Use of the original PIN will deletetemporary PIN.For questions, comments or troubleshooting, contact TheGenie Company at:1 Door Drive, Mount Hope Ohio, 44660or call 1-800-354-3643 or visit our website at:www.geniecompany.comKeypad MUST be mounted within sight of the garagedoor(s) at least 5 feet above floor and clear of any movingdoor parts.• Programming will not be lost during battery removal.1. Remove battery cover and batteries.2. Drill a 3/32” pilot hole for the top mounting screw.3. Install included screw into pilot hole, leaving 1/8” gapbetween the screw head and wall.4. Hook the slotted mount on back of keypad over thescrew.Wall1/8"Screwhead gap5. Mark and drill a 3/32” pilot hole for the bottom screwand secure keypad to the wall. (Do not over-tighten).6. Reinstall batteries.If the keypad back lighting fails to operate batteries mayrequire replacement.• Programming will not be lost during battery change.1. Remove battery cover and batteries.2. Replace batteries with same type alkaline (AAA) and checkfor proper direction of (+) and (-) terminals.Rechargeable batteries are NOT recommended.01/2018STEP 4) OPERATING THE KEYPAD WITH THE OPENER(S)STEP 5) MOUNTING THE KEYPAD* RESETTING THE KEYPAD (FACTORY DEFAULT):If the keypad has already been programmed or at anytime the programming should be erased and started fromthe factory default, follow these steps.1. Ensure that number pad back lighting is off.2. Press and hold the PROGRAM and UP/DOWN Keystogether for approximately 5 seconds.3. The LED will flash twice and all lights will go outindicating the keypad has been reset.4. Start at STEP 1 to sync the keypad to an opener.For use with Genie Intellicode® garage door openersKeypad OverviewActivate keypad by opening batterycompartment and pull protectivetab. Reinstall compartment door tobegin programming.TABNOTE: Keypad will remain active for 15 seconds after asuccessful entry is made. During this 15 seconds ANY key willoperate the opener.Current Production Openers1. Press and hold the program button until the roundLED turns blue, thenrelease. PROGRAMSET +PROGRAMSET +2. The round LED will go out and the long LED will beginflashing purple.3. Return to previousSTEP.PRGMSETTYPE 1 TYPE 2 TYPE 3There are 4 types of programming button pads. Type 1is shown in these steps. All buttons perform the samefunction and programming is the same for all types shownabove.Place operator into programming mode: TYPE 1-2-3-4Openers manufactured between 1995 to2011 and all external receiversRADIOSIGNALLEARNCODE CODELEARNSETSETOPENFORCECLOSECODELEARN LIMITMANUALorRADIOSIGNALLEARNCODERADIOSIGNALLEARNCODE1. Press & release Learn Code button once. The red LEDwill begin to flash.Place operator into programming mode:NOTE: Learn Code Buttons are normally located under lenscovers on earlier models.PUTTING OPENER INTO PROGRAMMING MODE:NOTE: The openers LEARN LED will timeout in 30 seconds. Programming must becompleted within 30 seconds.-OR-PROGRAMSET +PROGRAMSET +2. Return to previous STEP.REPLACING BATTERIESScan this code with a QR code reader appon a smart device to view a video of theseinstructions or visit www.geniecompany.comSTEP 2) CHANGING THE FACTORY DEFAULT PIN OF 3-5-7:1. Enter the factory default pin of 3-5-7.2. Press PROGRAM key once.3. Enter a new PIN of your choice (3-8 digits).4. Press PROGRAM key once.• Your PIN has been changed and your previous PIN will nolonger operate the keypad or opener.STEP 3) OPTIONAL:PROGRAMMING THE KEYPAD FOR MULTIPLE OPENERS (UP TO 3)Whether the keypad is brand new or you are just addingadditional openers to an existing keypad, this STEP assumesthat STEPs 1 & 2 have already been completed.Follow these steps to program opener 2 and/or 3 to thekeypad. (Only one PIN number can be used.)1. Ensure the keypad back lighting is off.2. Enter the current PIN.3. Press PROGRAM key twice. LED will blink once persecond.4. Enter total number of openers that keypad will beoperating (a total of “2” or “3” openers).5. Press PROGRAM key once. LED will blink twice and shutoff.• If LED did not blink twice and shut off, please seeRESETTING THE KEYPAD (FACTORY DEFAULT) section.• THE KEYPAD IS NOW READY TO PROGRAM TO MULTIPLEGARAGE DOOR OPENERS. CONTINUE WITH THE STEPSBELOW.PROGRAMMING TO MULTIPLE OPENERS CONTINUED1. Ensure the keypad back lighting is off.2. Place desired garage door opener (for door 2 or 3) intoPROGRAMMING MODE as shown to the right.3. Enter the PIN number on keypad.4. Press the UP/DOWN key once.5. Press the number of the desired door (door 2 or 3).6. Press the UP/DOWN key 3-4 times slowly until garagedoor opener operates.• Repeat steps 1 through 6 in this section to programanother door opener to this keypad (maximum of 3 doorsto 1 keypad).• This completes programming of multiple doors. See STEP4 MULTI-DOOR OPERATION for further instruction.+ PRGMSET+–PRGMSET+–PRGMSET+–TYPE 4STEP 1) PROGRAM THE NEW KEYPAD TO THE OPENERThe existing factory default Personal Identification Number(PIN) for this keypad is the number sequence: 3-5-7Sync the opener and the keypad by performing thefollowing:1. Ensure the keypad back lighting is off.2. Place garage door opener into PROGRAMMING MODEas illustrated in the column to the right.3. Press 3-5-7 in sequence on the keypad.4. Press the UP/DOWN key 3 to 4 times slowly untilgarage door opener operates.• This completes the programming of a single dooropener (door 1) and keypad.• IT IS RECOMMENDED THAT YOU CHANGE THIS PIN FROM THEEXISTING FACTORY DEFAULT SETTING of 3-5-7. See STEP 2 below.Activate keypad by opening battery compartment andpull protective tab. Reinstall compartment door to beginprogramming. |
Related manuals for Genie GK-R
Genie GUK-BX Instructions Manual
Genie GUK-BX Instructions Manual
Genie UNIVERSAL REMOTE Instructions Manual
Genie Universal Keypad Instructions Manual
Genie Wireless Keypad Instructions Manual
Genie Wireless Keypad Instructions Manual
Genie Series II Installation Instructions Manual
Genie GWKP-BX Operating Instructions Manual
Genie Wireless Keypad Operating Instructions Manual
Genie Wireless Keypad-IC Installation And Programming Instructions
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine