BOM: 3101A0QFH3C S6860-30HF Switch Installation Quick Start-5PW101H3C S6860-30HF 交换机 快速安装指南-5PW101Installation accessories 安装附件介绍The installation tools are not provided with the switch. Prepare them yourself as required.交换机不随机提供安装工具,请用户根据实际安装需求自己准备安装工具。Tool list 工具参考Mounting the switch in a rack 安装交换机到机柜Cable tie可拆卸式扎带Rack-mount rail kit A(with a long slide rail)长滑道和导轨Filler panel假面板M6 screw and cage nut(user supplied)M6 螺钉和浮动螺母(用户自备)Mounting bracketsand M4 screw挂耳和M4螺钉Wear an ESD wrist strap, and make sure the strap makes good skin contact and is reliably grounded.操作者需佩戴防静电腕带,确保防静电腕带与皮肤良好接触,并确认防静电腕带已经良好接地。!12Install the mounting brackets near the power module side 挂耳安装到靠近电源侧Attach the mounting brackets and chassis rails to the switch 安装挂耳和滑道导轨到交换机1Grounding cable andgrounding screw地线和接地螺钉Rack-mount rail kit B(with a super-shortslide rail) (optional)超短滑道和导轨(选配)Install the mounting brackets near the port side or power module side of the switch as needed. Attachthe chassis rails to the switch based on the mounting bracket installation position and rack depth.用户可以根据安装场景的需要,将挂耳安装在设备靠近端口侧或靠近电源侧,并根据机柜深度,在交换机侧面板的对应位置安装滑道导轨。For the S6860-30HF, rack-mount rail kit A is applicable to a rack with a depth (distance between thefront and rear rack posts) in the range of 621 to 793 mm (24.45 to 31.22 in).The chassis rail of rack-mount rail kit B can be installed through narrow-spacing installation orwide-spacing installation, which is applicable to a rack with a depth in the range of 330 to 505 mm(12.99 to 19.88 in) or 438 to 632 mm (17.24 to 24.88 in), respectively.对于S6860-30HF机型, 挂耳与长滑道和导轨配合安装适用于机柜前后方孔条间距范围为621~793mm。挂耳与超短滑道和导轨配合安装到机柜时,滑道导轨有正向安装和反向安装两种方式:导轨正向安装适用于机柜前后方孔条间距范围为330~505mm;导轨反向安装适用于机柜前后方孔条间距范围为438~632mm。Attaching the mounting brackets and chassis rails of rack-mount rail kit A to the switch挂耳与长滑道的导轨配合安装To use rack-mount rail kit A, make sure the front ends of the long slide rails reach out of the chassisrails. To use rack-mount rail kit B, make sure the super-short slide rails slide a minimum length of 90mm (3.54 in) into the chassis rails.为保证设备安装后的稳定性,使用长滑道和配套的导轨安装完成后,请确保长滑道的头部露出导轨。使用超短滑道和配套的导轨安装完成后,请确保超短滑道头部进入导轨的最小深度为90mm。Phillips screwdriver十字螺丝刀ESD wrist strap防静电腕带Marker记号笔Flathead screwdriver一字螺丝刀Install the mounting brackets near the port side 挂耳安装到靠近端口侧