HANYOUNG NUX DX Series Instruction Manual

Also see for DX Series: Instruction manual

Contents

HANYOUNG NUX DX Series Instruction Manual Manual pdf 1 page image

1⁕1 : The control operation can be changed in the parameter, SL9, andthe default is “reverse operation control (R)”.Suffix codeSafety informationDANGER indicates an imminently hazardous situationwhich, if not avoided, will result in death or serious injuryWARNING indicates a potentially hazardous situationwhich, if not avoided, could result in death or serious injuryCAUTION indicates a potentially hazardous situation which,if not avoided, may result in minor or moderate injuryAlerts declared in the manual are classified to Danger, Warning and Caution by their criticalityDANGERWARNINGCAUTIONDo not touch or contact the input/output terminals because they may causeelectric shock.• If the product is used with methods other than specified by themanufacturer, then it may lead to injury or property damage.• Please install an appropriate protective circuit on the outside if malfunctionor an incorrect operation may be a cause of leading to a serious accident.• Since this product does not have the power switch or a fuse, please installthose separately on the outside. (Fuse rating: 250V 0.5A)• To prevent damage or failure of this product, please supply the rated power voltage.• To prevent electric shock or equipment failure, please do not turn on thepower until completing wiring.• Since this is not explosion-proof structure, please do not use in a placewhere combustible or explosive gas is around.• Never disassemble, modify, or repair the product. There is a possibility ofmalfunction, electric shock, or a risk of fire.• Please turn off the power when mounting/dismounting of the product. Thisis a cause of electric shock, malfunction, or failure.• Since there is a possibility of electric shock, please use the product asmounted on a panel while the power is being supplied.• The contents of the instruction manual are subjective to change without prior notice.• Please make sure that the specification is the same as what you have ordered.• Please make sure that the product is not damaged during shipping.• Please use this product in a place where the ambient operatingtemperature is 0 ~ 50 ℃ (40 ℃ max, closely installed) and the ambientoperating humidity is 35 ~ 85 % R.H (without condensation).• Please use this product in a place where corrosive gas (such as harmfulgas, ammonia, etc.) and flammable gas do not occur.• Please use this product in a place where there is no direct vibration and alarge physical impact to the product.• Please use this product in a place where there is no water, oil, chemicals,steam, dust, salt, iron or others.• Please do not wipe this product with organic solvents such as alcohol,benzene and others. (Please use mild detergent)• Please avoid places where excessive amounts of inductive interferenceand electrostatic and magnetic noise occur.• Please avoid places where heat accumulation occurs due to directsunlight or radiant heat.• Please use this product in a place where the elevation is below 2,000 m.• Please make sure to inspect the product if exposed to water since there isa possibility of electric leakage or a risk of fire.• For thermocouple (TC) input, please use a prescribed compensation leadwire. (There is a temperature error if a general lead is used.)• For resistance temperature detector (RTD) input, please use a smallresistance of lead wire and the 3 lead wires should have the sameresistance. (There is a temperature error if the 3 lead wires do not havethe same resistance.)• Please put the input signal wire away from the power lines and load linesto avoid the effect of inductive noise.• The input signal wires and output signal wires should be separated from eachother. If it is not possible, please use shielded wires for the input signal wires.• For thermocouple (TC), please use ungrounded sensors. (There is apossibility of malfunction of product by electric leakage if a groundedsensor is used.)• If there is a lot of noise from the power line, installing an insulated transformeror a noise filter is recommended. The noise filter should be grounded on thepanel and the lead wire between the output of the noise filter and the powerterminal of the instrument should be as short as possible.• It is effective against noise if making the power lines of the product thetwisted pair wiring.• Please make sure the operation of the product before using since theproduct may not operate as it intends if the alarm function is not properly set.• When replacing the sensor, please turn off the power.• In case of the high frequent operation such as proportional operation,please use an auxiliary relay since the life span of the output relay will beshortened if it connects to the load without the rated margin. In this case,SSR output is recommended.⁕ Electromagnetic switch: proportion cycle: set 20 sec min.⁕ SSR: proportion cycle: set min.1 sec⁕ Contact output life expectancy:Mechanical - 1 million times min. (without load)Electrical – 100 thousand times min. (250 V a.c 3A: with rated load)• Please do not connect anything to the unused terminals.• Please connect wires properly after making sure the polarity of terminal.• Please use a switch or breaker (IEC60947-1 or IEC60947-3 approved)when the product is mounted on a panel.• Please install a switch or break near the operator to facilitate its operation.• If a switch or breaker is installed, please put a name plate that the poweris off when the switch or breaker is activated.• In order to use this product properly and safely, we recommend periodic maintenance.• Some parts of this product have limited expected life span and aged deterioration.• The warranty of this product (including accessories) is 1 year only when itis used for the purpose it was intended under normal condition.• When the power is being supplied there should be a preparation time forthe contact output. Please use a delay relay together when it is used as asignal on the outside of interlock circuit or others.• When the user replaces with a spare unit due to product failure or other reason,please check the compatibility since the operation can be varied by the differenceof setting parameters even though the model name and code are the same.• Before using a temperature controller, please check if there is atemperature difference between PV of the temperature controller and theactual temperature. If there is a temperature difference, please correct thetemperature difference with using the input correct parameter “SL-5”.DANGERWARNINGCAUTIONDigital Temperature ControllerDX seriesThank you for purchasing HANYOUNG product.Please check whether the product is the exactly same as you ordered.Before using the product, please read this instruction manual carefully.Please keep this manual where you can view at any timeINSTRUCTION MANUALMA0307E1208131381-3, Juan-Dong, Nam-Gu Incheon, Korea.TEL:(82-32)876-4697 FAX:(82-32)876-4696 http://www.hynux.netJl. cempaka blok F16, No.02 Delta Silicon II Cikarang Bekasi IndonesiaTEL : 62-21-8911-8120~4 FAX : 62-21-8911-8126HANYOUNGNUX CO.,LTDPT. HANYOUNG ELECTRONIC INDONESIAHEAD OFFICEINDONESIAFACTORYModel Code DescriptionDX ☐ - ☐ ☐ ☐ ☐ ☐ ☐ Digital temperature controllerDimension2 48(W) × 96(H) ㎜3 96(W) × 48(H) ㎜4 48(W) × 48(H) ㎜7 72(W) × 72(H) ㎜9 96(W) × 96(H) ㎜InputK K themocoupleJ J themocoupleR R themocoupleD RTD: KPt 100 ΩP RTD: Pt 100 ΩV 1 - 5 V d.cC 4 - 20 ㎃ d.cF 0 - 10 V d.cControloutputM Relay contact outputC Current output (4 - 20 ㎃ d.c)S S.S.R (voltage pulse output, 12 V d.c)Alarm output S Alarm output: 1 contact (model: DX4)W Alarm output: 2 contacts(all model except DX4)Option A Retransmission output (4 - 20 ㎃ d.c)N None (no retransmission output for DX4, DX7)Control operation ⁕1 R Reverse operation control(heating control)D Direct operation control(cooling control)Power supply • 100 - 240 V a.cC 24 V d.c/a.c