Haier HSU-07HEA03/R2 Operation Manual

Also see for H2SM-(9+12)HEA03/R2: Installation manual Operation manual Operation manual Operation manual

Contents

Haier HSU-07HEA03/R2 Operation Manual Manual pdf 3 page image

3OperationAir Flow Direction AdjustmentAUTO COOL DRY FAN HEAT2.Select operation modePress FAN button. For each press, fan speed changes asfollows:Press MODE button. For each press, operation modechanges as follows:Remote controller:Remote controller:Press buttonEvery time the button is pressed, temp.settingincrease 1 oC,if kept depressed, it will increaserapidlyEvery time the button is pressed, temp.settingdecrease 1 oC,if kept depressed, it will decreaserapidlySelect a desired temperature.4.Fan speed selection3.Select temp.settingAir conditioner is running under displayed fan speed.When FAN is set to AUTO, the air conditionerautomatically adjusts the fan speed according to roomtemperature.LOW MED HI AUTO1. Unit startPress ON/OFF on the remote controller, unit starts.Clock setOperationModeAUTODisplay Board RemoteController NoteCOOLDRYHEATFAN nothingIn DRY mode, when room temperature becomeslower than temp.setting+2 oC,unit will run intermittentlyat LOW speed regardless of FAN setting.Under the mode of auto operation, air conditioner willautomatically select Cool or Heat operation accordingto room temperature.air conditioner automatically adjusts the fan speedtemperature.When FAN is set to AUTO, theaccording to roomIn FAN operation mode, the unit will not operate inCOOL or HEAT mode but only in FAN mode ,AUTO isnot available in FAN mode.And temp.setting is disabled.In FAN mode,SLEEP operation is not available.Vertical flapPos.1 Pos.2 Pos.3Pos.4 Pos.5 Pos.6 (Auto swing)1.Status display of air flowWhen restart after remote turning off, the remotememorize the previousMove the vertical blade by a knob on airto adjust left and right direction referring to Fig.2.Left and right air flow adjustment(manual)Cautions:When adjusting the flap by hand,turn off the unit.When humidity is high,condensate water might occuradjusted to left orIt is advisable not to keep horizontal flap at downwardposition for a long time in COOLor DRYotherwise, condensate water might occur.conditionertemperature is below 16 oC, do not use it in theTest operation:Use this switch in the test operation when the roomnormal operation.your finger from the switch: the coolingContinue to press the test operationswitch for more than 5 seconds. Afteryou hear the "Pi" sound twice, releaseTest operation switch is the same as emergency switch.operation starts with the air flow speed "Hi".Emergency operation and test operationPi Piat air outlet if all vertical louvers areright.mode ,controller will automaticallyNote:set swing position.Remote controllerBase OperationPress CLOCK button, "AM" or "PM" flashes.Press or to set correct time. Each presschange quickly. After time setting is confirmed,press SET,"AM "and "PM" stop flashing,while clock starts working.or decrease 1min. If the button is kept pressed,time willwill increasePOWER/SOFTCEmergency Operation:Use this operation only when the remote controlleris defective or lost.When the emergency operation switch ispressed,the" Pi "sound is heard once, whichthe start of this operation.In this operation, the system automatically selectsthe operation modes,cooling or fan or heat,according to the room temperature..It is not possible to operate in dry mode.Roomtemperature Operationmode Designatedtemperature Timermode Air flowABOVE 23 OCBELOW 23OCCOOLINGHEAT 23O C26 OC NONOAUTOMATICAUTOMATICPi(cooling only uint)Room temperature Operationmode Designatedtemperature Timermode Air flowBELOW 23OC FAN 26OC NO AUTOMATICmeansPOWER/SOFT124