2. The wiring method should be in line with the local wiring standard.3. After installation, the power plug should be easily reached.4. A breaker should be incorporated into fixed wiring. The breaker should beall-pole switch.Outdoor unitInstall according to Drawing for the installation of indoor and outdoor unitsƽand the bending radius should be 30 (1 1/6) to 40 mm (1 4/7) or longer.Connecting the pipe of gas side first makes working easier.ƽThe connection pipe is specialized for R410A.ƽInstallation of Outdoor UnitHalf union Flare nutTorque wrenchThe standard pipe length is 7m (27 9/16) . If it is over 7m (27 9/16) , the functionof the unit will be affected. If the pipe has to be lengthened, the refrigerant shouldbe charged, according to 20 g/m (0.018 oz/inch). But the charge of refrigerant mustbe conducted by professional air conditioner servicer. Before adding additionalrefrigerant, perform air purging from the refrigerant pipes and indoor unit usinga vacuum pump,thenSpannerForced fastening without careful centering maydamage the threads and cause a leakage of gas.Pipe Diameter(ǿ) Fastening torqueLiquid side6.35mm(1/4") 18N.m/13.3Ft.lbsLiquid/Gas side9.52mm(3/8") 42 N.m/30.1Ft.lbsGas side 12.7mm(1/2") 55N.m/40.6Ft.lbsGas side 15.88mm(5/8") 60 N.m/44.3Ft.lbsConnection of pipescharge additional refrigerant.Outdoor unitIndoor unitABOutdoor unitIndoor unitABABOutdoor unitIndoor unitOil trapCAUTIONMax.Elevation: Amax=1m●In case the elevation A is more●than 5m, oil trap shoud beinstalled every 5~7mMax. Length: Bmax=15m●In case the pipe length B is●more than 10m, the refrigerantshould be charged, accordingto 20 g/m.3ConnectionIf the drain-elbow is used,ƽ please attach it as figure. (Note:Only for heat pump unit.)1.Open the handle on low side of manifold and2. operate vacuum pump. If the low3. After the completion of vacuuming, close the handle ‘Lo’ in gaugemanifold andstop the operation of the vacuum pump.Attaching Drain-ElbowPurging Method:To use vacuum pumpOpen the valve rod stem the 2-way valve counterclockwise to 90 degrees.4.After 6 seconds, close the 2-way valve and inspect for gas leakage.Power cable:HSU12VHJ(DB)-WOutdoor unit32^PowerWiring1 )(N )(L )(C 321 )(N )(L )(CIndoor unitPower cable:ƽƽƽƽƽƽTake off the panel(top), by removing the 5 screws.Remove the plugs on the conduit plate.Temporarily mount the conduit tubes on the conduit plate.Connect both the power supply and unit wire harness tothe corresponding terminals on the terminal board.Ground the unit in accordance with local codes.Allow several extra inches of wire for making wiringconnections.Use lock nuts to secure conduit tubes.ƽTo bend a pipe, be careful not to crush the pipe,HSU09VHJ(DB)-WHSU24VHJ(DB)-WHSU18VHJ(DB)-WHSU12XCK-WHSU09XCK-WPower cable:Power cable:Power cable:Power cable:1. If the fuse on PC board is broken please change it with the type ofT. 3.15A/250V(indoor unit),25A/250V(outdoor unit).4wire 18AWG2wire with ground 16AWG2wire with ground 16AWG2wire with ground 12AWG2wire with ground 12AWG2wire with ground 16AWG2wire with ground 16AWGOutdoor unitIndoor unitRemove the service port cap of the 3-way valve and the valve stem cap for bothvalves. Connect the low pressure hose from the manifold set to the 3-way valve.Connect the center hose to the vacuum pump.side gauge reaches a vacuum immediately, ensure the hoses are connectedproperly and the low side manifold handle is open.Vacuum for a minimum of 15 minutes and check the gauge for a proper vacuum.Leave the hoses connected and checkthe vacuum level again in 1-2 minutes. If you lose the vacuum, ensure allconnections are tight and flare the tubes again if needed.Ensure that no dirt or debris enters the pipe.Control WiringAll models: Control cable: 4wire, 18AWG