Hameg HM303-6 Manual

Also see for HM303-6: Operator's manual Service manual

Contents

5Subject to change without notice35 MHz Analog Oscilloscope HM303-6Valid at 23 °C after a 30 minute warm-up periodVertical DeflectionOperating Modes: Channel I or II onlyChannels I and II (alternate or chopped)Sum or Difference of CH I and CH IIInvert: CH IIXY Mode: via CH I (X) and CH II (Y)Bandwidth: 2 x 0 to 35 MHz (-3 dB)Rise Time: ‹ 10 nsOvershoot: max. 1%Deflection Coefficients: 1-2-5 Sequence1 mV/div. – 2 mV/div.: ± 5 % (Bandwidth 0 – 10 MHz (-3 dB))5 mV/div. – 20 V/div.: ± 3 % (Bandwidth 0 – 35 MHz (-3 dB))Variable (uncalibrated): › 2.5 : 1 to › 50 V/div.Input Impedance: 1 MΩ II 20 pFInput Coupling: DC, AC, GND (ground)Max. Input Voltage: 400 V (DC + peak AC)TriggeringAutomatic (Peak to Peak): 20 Hz – 50 MHz (≥ 5 mm)50 MHz - 100 MHz (≥ 8 mm)Normal with Level Control: 0 - 50 MHz (≥ 5 mm)50 MHz – 100 MHz (≥ 8 mm)Trigger Indicator: LEDSlope: positive or negativeSources: Channel I or II, CH I / CH II alternate(≥ 8 mm), Line and ExternalCoupling: AC: 10 Hz – 100 MHzDC: 0 – 100 MHzLF: 0 – 1.5 kHzTrigger Indicator: LEDExternal Trigger Signal: ≥ 0.3 V pp (30 Hz – 50 MHz)Active TV sync. separator: pos. and neg.Horizontal DeflectionTime Base: 0.2 s/div. – 0.1 μs/div. (1-2-5 Sequence)Accuracy: ± 3 %Variabel (uncalibrated): › 2.5:1 to › 0.5 s/div.X Magnification x 10: up to 10 ns/div.Accuracy: ± 5 %Hold-Off Time: variable to approx. 10 : 1XYBandwidth X Amplifier: 0 – 2.5 MHz (-3 dB)XY Phase shift ‹ 3°: ‹ 120 kHzComponent TesterTest Voltage: approx. 7 V rms (open circuit)Test Current: max. 7 mA rms (short-circuit)Test Frequency: approx. 50 HzTest Connection: 2 banana jacks 4 mm ØOne test circuit lead is grounded via protective earth (PE)MiscellaneousCRT: D14-363GY, 8 x 10 cm with internal graticuleAcceleration Voltage: approx. 2 kVTrace Rotation: adjustable on front panelCalibrator Signal (Square Wave): 0.2 V ± 1 %, ≈ 1 kHz/1 MHz (tr ‹ 4 ns)Power Supply (Mains): 105 – 253 V, 50/60 Hz ± 10 %, CAT IIPower Consumption: approx. 36 Watt at 230 V/50 HzAmbient temperature: 0° C...+ 40° CSafety class: Safety class I (EN61010-1)Weight: approx. 5.4 kgDimensions (W x H x D): 285 x 125 x 380 mmAccessories supplied: Line Cord, operator’s manual, 2 Probes 1:1 / 10:1 (HZ154)HM303-6E/260107/ce · Subject to alterations · © HAMEG Instruments GmbH · ® Registered Trademark · DQS-certified in accordance with DIN EN ISO 9001:2000, Reg.-No.: DE-071040 QMHAMEG Instruments GmbH · Industriestr. 6 · D-63533 Mainhausen · Tel +49 (0) 6182 800 0 · Fax +49 (0) 6182 800 100 · www.hameg.com · info@hameg.comw w w . h a m e g . c o mSpecifications