Hans Grohe Ecostat Comfort 13116 Series Instructions For Use/assembly Instructions

Also see for Ecostat Comfort 13114 Series: Instructions for use/assembly instructions Instructions for use/assembly instructions Instructions for use/assembly instructions Instructions for use/assembly instructions Instructions for use/assembly instructions

4EnglishAssembly (see page 32)Safety NotesGloves should be worn during installation to prevent crushing and cuttinginjuries.The product may only be used for bathing, hygienic and body cleaningpurposes.The product may not be used as a holding handle. A separate handle must beinstalled.Children as well as adults with physical, mental and/or sensoric impairmentsmust not use this product without proper supervision. Persons under theinfluence of alcohol or drugs are prohibited from using this product.The hot and cold supplies must be of equal pressures.Installation Instructions• Prior to installation, inspect the product for transport damages. After it has beeninstalled, no transport or surface damage will be honoured.• The pipes and the fixture must be installed, flushed and tested as per theapplicable standards.• The plumbing codes applicable in the respective countries must be observed.• The product is not designed to be used with steam baths!ECOSTAT in conjunction with flow heaters• If fitting a hand shower remove the water limiter from the shower.• If the continuous water heater causes any problems, or you have different waterpressures you must install a water limiter to the cold supply, (ordered separate-ly,article number 97510000).Technical DataOperating pressure: max. 1 MPaRecommended operating pressure: 0,1 - 0,5 MPaTest pressure: 1,6 MPa(1 MPa = 10 bar = 147 PSI)Hot water temperature: max. 70°CRecommended hot water temp.: 65°CCentre distance: 150±12 mmConnections G 1/2: cold right - hot leftThermal disinfection: 70°C / 4 min• Safety against backflow• The product is exclusively designed for drinking water!Symbol descriptionDo not use silicone containing acetic acid!Adjustment (see page 33)After the installation, the output temperature of the thermostat must be checked. Acorrection is necessary if the temperature measured at the output differs from thetemperature set on the thermostat.Safety Function (see page 33)The desired maximum temperature for example max. 42º C can be pre-set thanksto the safety function.Cleaning (see page 35)Maintenance (see page 35)• The check valves must be checked regularly according to EN 806-5 inaccordance with national or regional regulations (at least once a year).• To guarantee the smooth running of the thermostat, it is necessary from time totime to turn the thermostat from total hot to total cold.)Dimensions (see page 36)Flow diagram (see page 36) Shower outlet Tub outletSpare parts (see page 37)XXX = Colors000 = Chrome Plated140 = Brushed Bronze340 = Brushed Black Chrome670 = Matt Black700 = Matt White800 = Stainless Steel Optic990 = Gold PlatedOperation (see page 34)Test certificate (see page 32)Fault Cause RemedyInsufficient water - Supply pressure inadequate - Check water pressure (If a pump has been installedcheck to see if the pump is working).- Regulator filter dirty - Clean filter in front of the mixer and on the MTC-ther-mo cartridge- Shower filter seal dirty - Clean filter seal between shower and hoseCrossflow, hot water being forced into cold waterpipe, or vice versa, when mixer is closed- Backflow preventers dirty or leaking - Clean backflow preventers, exchange if necessarySpout temperature does not correspond withtemperature set- Thermostat has not been adjusted - Adjust thermostat- Hot water temperature too low - Increase hot water temperature to 42 ºC to 65 ºCTemperature regulation not possible - thermo cartridge calcified - Exchange thermo cartridge- Dirt or sedimentation on valve seat, shut-off unitdamaged- Clean or exchange shut-off unitInstantaneous heater didn't work with thermostat - Filters are dirty - Clean the filter / exchange filter- check valve hasn't moved back - Exchange check valves- Flow limiter in handshower isn’t removed - Remove flow limiterShower or spout dripping - Dirt or sedimentation on valve seat, shut-off unitdamaged- Clean or exchange shut-off unit