Hans Grohe Ecostat E 13125000 Instructions For Use/assembly Instructions

Also see for Ecostat E 13125000: Assembly instructions

Assembly see page 31Fault Cause RemedyInsufficient water - Supply pressure inadequate - Check water pressure (If a pump has been installedcheck to see if the pump is working).- Filters are dirty (#96922000) - Clean filter in front of the mixer and on the MTC-thermo cartridge (#96922000)- Shower filter seal dirty - Clean filter seal between shower and hoseCrossflow, hot water being forced into cold water pipe,or vice versa, when mixer is closed- Backflow preventers dirty or leaking - Clean backflow preventers, exchange if necessarySpout temperature does not correspond with tempera-ture set- Thermostat has not been adjusted - Adjust thermostat- Hot water temperature too low - Increase hot water temperature to 42 ºC to 65 ºCTemperature regulation not possible - thermo cartridge calcified - Exchange thermo cartridgeShower or spout dripping - Dirt or sedimentation on valve seat, shut-off unit dam-aged- Clean or exchange shut-off unitInstantaneous heater didn't work with thermostat - Ecostop limit stop washer not turned axially through180°- Turn the limit stop washer (98916000) axially through180°- Flow limiter in handshower isn’t removed - Remove flow limiter- Filters are dirty - Clean the filter / exchange filter- check valve hasn't moved back - Exchange check valvesCleaning (see page 38)Test certificate (see page 40)Spare parts (see page 36)Flow diagram (see page 34) Shower Bath tubDimensions (see page 34)Operation (see page 35)ECOSTOP (see page 33)Adjustment (see page 32)After the installation, the output temperature of the thermostat must bechecked. A correction is necessary if the temperature measured at theoutput differs from the temperature set on the thermostat.Safety Function (see page 32)The desired maximum temperature for example max. 42º C can be pre-set thanks to the safety function.Do not use silicone containing acetic acid!Symbol descriptionSafety NotesGloves should be worn during installation to prevent crushing and cuttinginjuries.Children as well as adults with physical, mental and/or sensoric impairmentsmust not use this product without proper supervision. Persons under the influ-ence of alcohol or drugs are prohibited from using this product.The product may only be used for bathing, hygienic and body cleaning pur-poses.The hot and cold supplies must be of equal pressures.Installation Instructions• Prior to installation, inspect the product for transport damages.After it has beeninstalled, no transport or surface damage will be honoured.• The product is not designed to be used with steam baths!• The pipes and the fixture must be installed, flushed and tested as per the applica-ble standards.• The plumbing codes applicable in the respective countries must be oberserved.ECOSTAT in conjunction with flow heaters• If fitting a hand shower remove the water limiter from the shower.• In case of problems with the continuous water heater or of greatly varying waterpressures, you must install the water limiter (comprised in the delivery, articlenumber 97510000) in the cold water supply.• Thermostatic mixer Shower: When mounting the ECOSTOP limit stop washer (Art.No. 98916000) in connection with flow heaters, turn it axially through 180°before attaching it.Technical DataOperating pressure: max. 1 MPaRecommended operating pressure: 0,1 - 0,5 MPaTest pressure: 1,6 MPa(1 MPa = 10 bar = 147 PSI)Hot water temperature: max. 70°CRecommended hot water temp.: 65°CThermal disinfection: max. 70°C / 4 min• Safety against backflow• The product is exclusively designed for drinking water!EnglishMaintenance (see page 33)• The mixer is equipped with check valves. The check valves must bechecked regularly according to DIN EN 1717 in accordance withnational or regional regulations (at least once a year).• To guarantee the smooth running of the thermostat, it is necessaryfrom time to time to turn the thermostat from total hot to total cold.4