Hans Grohe MySelect S 150 Semipipe 27239000 Instructions For Use/assembly Instructions

Also see for MySelect S 150 Semipipe 27239000: Instructions for use/assembly instructions Instructions for use/assembly instructions

4EnglishAssembly (see page 32)Safety NotesGloves should be worn during installation to prevent crushing and cuttinginjuries.The product may only be used for bathing, hygienic and body cleaningpurposes.The arm of the shower head is intended only to hold the shower head. Do notload it down with other objects!Children as well as adults with physical, mental and/or sensoric impairmentsmust not use this product without proper supervision. Persons under theinfluence of alcohol or drugs are prohibited from using this product.Do not allow the streams of the shower touch sensitive body parts (such as youreyes). An adequate distance must be kept between the shower and you.The product may not be used as a holding handle. A separate handle must beinstalled.The hot and cold supplies must be of equal pressures.Installation Instructions• Prior to installation, inspect the product for transport damages. After it has beeninstalled, no transport or surface damage will be honoured.• The pipes and the fixture must be installed, flushed and tested as per theapplicable standards.• The plumbing codes applicable in the respective countries must be observed.• The installation dimensions stated in these installation instructions are ideal forpeople of approximately 1800 mm in body height. The dimensions can bealtered if required. In this case, pay attention to the fact that a change ofinstallation height will also change the minimum height, and that the alteredmounting dimensions must be taken into consideration.• During installation of the product by qualified trained personnel, make sure thatthe entire fastening surface is even and smooth (no protruding seams or tileoffset), that the finish of the wall is suitable to apply the product and has noweak points.• The premounted filter insert must be used to ensure a normal flow of the showerand to prevent dirt from entering through the pipes. Dirt entering can affect thefunction and/or lead to damages to the shower. Hansgrohe will not be heldliable for this type of damage.• The product is not designed to be used with steam baths!• If the continuous water heater causes any problems, or you have different waterpressures you must install a water limiter to the cold supply, (ordered separate-ly,article number 97510000).Technical DataOperating pressure: max. 1 MPaRecommended operating pressure: 0,15 - 0,5 MPaTest pressure: 1,6 MPa(1 MPa = 10 bar = 147 PSI)Hot water temperature: max. 70°CRecommended hot water temp.: 65°CCentre distance: 150±12 mmConnections G 1/2: cold right - hot leftThermal disinfection: max. 70°C / 4 min• Safety against backflow• The product is exclusively designed for drinking water!Symbol descriptionDo not use silicone containing acetic acid!Dimensions (see page 31)Flow diagram (see page 31)Dismounting (see page 33)Adjustment (see page 34)After the installation, the output temperature of the thermostat must be checked. Acorrection is necessary if the temperature measured at the output differs from thetemperature set on the thermostat.Safety Function (see page 34)The desired maximum temperature for example max. 42º C can be pre-set thanksto the safety function.Cleaning (see page 36)Maintenance (see page 38)• The check valves must be checked regularly according to DIN EN 1717 inaccordance with national or regional regulations (at least once a year).• To guarantee the smooth running of the thermostat, it is necessary from time totime to turn the thermostat from total hot to total cold.Spare parts (see page 39)Special accessories (order as an extra)tile-matching-disk Chrome Plated #95163000 (see page 39)Operation (see page 35)Test certificate (see page 40)Fault Cause RemedyInsufficient water - Supply pressure inadequate - Check water pressure (If a pump has been installedcheck to see if the pump is working).- Filters are dirty (#96922000) - Clean filter in front of the mixer and on the MTC-ther-mo cartridge- filter insert shower dirty - Clean filter insert between shower and hoseCrossflow, hot water being forced into cold waterpipe, or vice versa, when mixer is closed- Backflow preventers dirty or leaking - Clean backflow preventers, exchange if necessarySpout temperature does not correspond withtemperature set- Thermostat has not been adjusted - Adjust thermostat- Hot water temperature too low - Increase hot water temperature to 42 ºC to 65 ºCTemperature regulation not possible - thermo cartridge calcified - Exchange thermo cartridgeInstantaneous heater didn't work with thermostat - Filters are dirty - Clean the filter / exchange filter- check valve hasn't moved back - Exchange check valves- Flow limiter in handshower isn’t removed - Remove flow limiter