Hans Grohe Talis Puro Showerpipe Instructions For Use/assembly Instructions

4 Assembly see page 12Fault Cause RemedyInsufficient water - Supply pressure inadequate - Check water pressure (If a pump has been installedcheck to see if the pump is working).- Filters are dirty (#96922000) - Clean filter in front of the mixer and on the MTC-thermo cartridge- filter insert shower dirty (#97708000) - Clean filter insert between shower and hoseCrossflow, hot water being forced into cold water pipe,or vice versa, when mixer is closed- Backflow preventers dirty or leaking - Clean backflow preventers, exchange if necessarySpout temperature does not correspond with tempera-ture set- Thermostat has not been adjusted - Adjust thermostat- Hot water temperature too low - Increase hot water temperature to 42 ºC to 65 ºCTemperature regulation not possible - thermo cartridge calcified - Exchange thermo cartridgeInstantaneous heater didn't work with thermostat - Filters are dirty (#96922000) - Clean the filter / exchange filter- check valve hasn't moved back - Exchange check valves- Flow limiter in handshower isn’t removed - Remove flow limitertile-matching-disk chrome plated #952391000 (see page 20)Spare parts (see page 20)Cleaning (see page 16)Operation (see page 15)To empty the overhead shower after use, hold it in a slightly inclinedposition.Flow diagram (see page 19) overhead shower Hand showerDimensions (see page 19)Maintenance (see page 18)The mixer is equipped with check valves. The check valves must bechecked regularly according to DIN EN 1717 in accordance withnational or regional regulations (at least once a year).Adjustment (see page 14)After the installation, the output temperature of the thermostat must bechecked. A correction is necessary if the temperature measured at theoutput differs from the temperature set on the thermostat.Do not use silicone containing acetic acid!Symbol descriptionTechnical DataOperating pressure: max. 1 MPaRecommended operating pressure: 0,15 - 0,5 MPaTest pressure: 1,6 MPa(1 MPa = 10 bar = 147 PSI)Hot water temperature: max. 70°CRecommended hot water temp.: 65°CThermal disinfection: max. 70°C / 4 minCentre distance: 150 ± 12 mmConnections R1/2: cold right - hot leftThe product is exclusively designed for drinking water!Safety NotesGloves should be worn during installation to prevent crushing and cuttinginjuries. The shower system may only be used for bathing, hygienic and bodycleaning purposes.The arm of the shower head is intended only to hold the shower head. Do notload it down with other objects!Children as well as adults with physical, mental and/or sensoric impairmentsmust not use this product without proper supervision. Persons under the influ-ence of alcohol or drugs are prohibited from using this product.Do not allow the streams of the shower touch sensitive body parts (such as youreyes). An adequate distance must be kept between the shower and you.The product may not be used as a holding handle. A separate handle must beinstalled.The shower system may only be used for bathing, hygienic and body cleaningpurposes.The hot and cold supplies must be of equal pressures.Installation Instructions• Prior to installation, inspect the product for transport damages. After it has beeninstalled, no transport or surface damage will be honoured.• The pipes and the fixture must be installed, flushed and tested as per the applica-ble standards.• The plumbing codes applicable in the respective countries must be oberserved.• The installation dimensions stated in these installation instructions are ideal forpeople of approximately 1800 mm in body height. The dimensions can bealtered if required. In this case, pay attention to the fact that a change of instal-lation height will also change the minimum height, and that the altered mountingdimensions must be taken into consideration.• During installation of the product by qualified trained personnel, make sure thatthe entire fastening surface is even and smooth (no protruding seams or tileoffset), that the finish of the wall is suitable to apply the product and has no weakpoints.• The premounted filter insert must be used to ensure a normal flow of the showerand to prevent dirt from entering through the pipes. Dirt entering can affect thefunction and/or lead to damages to the shower. Hansgrohe will not be heldliable for this type of damage.• If required, the bottom part of the pipe between the fixture and the shower headcan be shortened with a fine-toothed saw.• The product is not designed to be used with steam baths!• If the continuous water heater causes any problems, or you have differentwater pressures you must install a water limiter to the cold supply, (orderedseparately,article number 97510000).EnglishSpecial accessories (order as an extra)Safety Function (see page 14)Test certificate (see page 20)