Harken 3294 Instructions Manual

Harken 3294 Instructions Manual Manual pdf 1 page image

INSTRUCTIONSV™BlocksN15W24983 Bluemound Road • Pewaukee, WI 53072 U.S.A.Telephone: (262) 691-3320 • Fax: (262) 691-3008 • Web: harken.com • E-mail: harken@harken.comYou Must Supply1. Primary support loop or lashing lineHarken is not liable or responsible for choosing line used to secure blocks. Goto Harken Limited Warranty at www.harken.com/manuals for complete details.Refer to the “Specifications Chart” above and use a loop/lashing with amaximum working load that meets or exceeds the maximum working loadlisted. If working with breaking loads, use a breaking load that is four (4) timesthe maximum working load listed.Important information on choosing line, knots, and splices:See www.harken.com/knots.2. Secondary lashing lineUse a small diameter line for lashing the primary supporting loop or lashingnear the head. Line length and diameter will vary depending on block.WARNING! Knots weaken line considerably. Work with a qualifiedrigger or line manufacturer on securing line. Select high-strengthloops using the instructions in “1” at left, or consult rigger forrecommendations on lashing.SpecificationsNote: See replacement part numbers on last page.MouthØWARNING! Strictly follow all instructions to avoid an accident, damage to your vessel,personal injury or death. See www.harken.com/manuals for additional safety information. = Incorrect. Avoid to prevent accidents.V blocks mount using soft attachment methods. The primary support lashings or loops pass through the block's mouth. A secondary lashing keeps the blockaligned. Cheeks are 3D-molded carbon or machined aluminum. The bearing system combines axial and thrust bearings into a single bearing set of angledtitanium rollers.Sheave diameter Max line Ø Mouth Ø Maximum working load Breaking loadPart No.* Description mm in mm in mm in kg lb kg lb3294, 3294AL 1.5T single 47 1.85 9 11/32 15 .59 1500 3300 3000 66003366AL 1.5T wide 47 1.85 2x 9 2x 11/32 15 .59 1500 3300 3000 66003295, 3295AL 3.0T single 56 2.20 11 7/16 20 .785 3000 6600 6000 132003367AL 3.0T wide 56 2.20 2X 11 2X 7/16 20 .785 3000 6600 6000 132003296, 3296AL 5.0T single 62 2.44 13 1/2 20 .785 5000 11000 10000 220003362AL 5.0T wide 62 2.44 2X 14 2X 9/16 20 .785 5000 11000 10000 220003297, 3297AL 6.5T single 82 3.23 16 5/8 26 1.02 6500 14300 13000 286003368AL 6.5T wide 82 3.23 2X 16 2X 5/8 26 1.02 6500 14300 13000 286003363AL 8T single 104 4.09 18 11/16 42 1.67 8000 17600 16000 352003369AL 8T wide 104 4.09 2X 18 2X 11/16 42 1.67 8000 17600 16000 352003370AL 12T single 120 4.75 22 7/8 51 2.03 12000 26400 24000 528003371AL 16T single 140 5.5 26 1 1/16 63 2.49 16000 35200 32000 704003372AL 20T single 155 6.13 30 1 3/16 64 2.52 20000 44000 40000 88000*Block cheeks are carbon or aluminum. AL signifies aluminum cheeks.HeadMouthCheekSheavePrimary supportloop or lashingSecondarylashingTermsCarbon and Aluminum V BlocksSecondarylashingtunnel

/ 4

Related manuals for Harken 3294