Harman Kardon AVR 160 Owner's Manual

Also see for AVR 160: Service manual

Harman Kardon AVR 160 Owner's Manual Manual pdf 34 page image

34ADVANCED FUNCTIONSA/V SYNC DELAY: This line allows you to compensate for a “lip sync”problem, in which a source device or the video display introduces a significantamount of video processing that causes the audio and video parts of thesignal to lose synchronization. You may delay the audio for all channels by upto 180 milliseconds to compensate.NOTE: Adjusting the A/V Sync Delay using the Delay Button on the remoteis recommended, so as to view the picture while adjusting the audio delay.With the program playing, press the Delay Button, and the A/V SYNCDELAY message will appear on the front panel and in the semi-OSD display.Press the OK Button to display the current delay setting, and use the M NButtons to adjust the setting until the picture and sound are back in sync.Step four – Setting channel output LevelsmanuallyFor a conventional 2-channel receiver, the balance control affects the stereoimaging by adjusting the relative loudness of the left and right channels.With up to seven main channels, plus a subwoofer, imaging becomes bothmore critical and more complex. The goal is to ensure that each channel isheard at the listening position with equal loudness.EzSet/EQ calibration can handle this critical task for you, simply andautomatically. However, the AVR’s Level Adjust menu allows you to calibratethe levels manually, either using the system’s test tone or while playingsource material.Make sure all speakers have been placed and connected correctly.1.Adjust the number of speakers, crossover, distance and sub mode for each2.speaker in your system, as described in Step Three.Measure the channel levels in one of these ways, and adjust the channel3.levels using the Level Adjust menu:Preferably, use a handheld SPL meter set to the C-Weighting, Slowa)scale. Adjust each channel so that the meter reads 75dB.By ear. Adjust the levels so that all channels sound equally loud.b)If you are using a handheld SPL meter with source material, such asc)a test disc or an audio selection, play it and adjust the AVR’s mastervolume control until the meter measures 75dB.Press the OSD Button to display the Master menu, and then navigate to theMANUAL SETUP line. Press the OK Button to display the Manual Setup menu.Select the LEVEL ADJUST line and press the OK Button to display the LevelAdjust menu. See Figure 30.Figure 30 – Level Adjust MenuAll of the speaker channels will appear with their current level settings.Channel Reset: To reset all of the levels to their factory defaults of 0dB,navigate to this line and change the setting to ON. The levels will be reset,and this setting will remain ON until one of the channel levels is adjusted.If you are using an external source to set your output levels, navigate to eachchannel and use the M N Buttons to adjust the level as desired. If you wouldlike to set your levels using the AVR 160’s internal test tone, adjust the TESTTONE SEQ and TEST TONE lines as follows.Test Tone SEQ: When this setting reads AUTO, the test tone willautomatically circulate to all channels, pausing for a few moments at eachchannel for several seconds, as indicated by the blinking cursor. Adjust thelevel for any channel when the test tone is paused there by using the M NButtons. You may also use the KL Buttons at any time to move the cursorto another line, and the test tone will follow the cursor.When this setting reads MANUAL, the test tone will not move to the nextchannel until you use the KL Buttons.Test Tone: This line determines whether the test tone is active. To begin theprocess of setting the levels, use the M N Buttons to change the setting toON. Any time you manually move the cursor out of the channel listings areaof the screen, this setting will automatically change to OFF, stopping the testtone.Individual Channels: If you are using an external source to set youroutput levels, navigate to each channel and use the M N Buttons to adjustthe level, between –10dB and +10dB. The level settings are global for allsources and surround modes.When you have finished adjusting the speaker levels, select the BACK TOMANUAL SETUP option or press the OSD Button. Record the level settings inTable A6 in the appendix.auDIo SettInGSTo adjust other audio settings, such as the tone controls, press the OSD Buttonto display the Master menu. With the cursor pointing to INPUT SETUP, pressthe OK Button to display the Input Setup menu, where the source, its title, itscomponent video and audio inputs, and Auto Polling status may be adjusted,as described in the Initial Setup section. However, this section will focus onthe four audio settings:BXR: Enhances bass performance when playing MP3 tracks. Select On, orleave at the default Off setting for non-MP3 audio.Tone: Determines whether the treble and bass controls are active. Whenit’s OUT, the tone controls are “flat”, with no changes. When it’s IN, the bassand treble frequencies are boosted or cut, depending upon the tone-controlsettings. When an analog audio source is in use and the 2-Channel Stereosurround mode is selected, setting the Tone Control to “OUT” places the unit inanalog bypass mode.Treble and Bass: Boost or cut the high or low frequencies by up to 10dB,2dB at a time, by using the M N Buttons. The default setting is 0dB.When you have finished, press the OSD Button.