Harman Kardon AVR430 Service Manual

Also see for AVR 430: Manual Brochure & specs Brochure & specs Service manual Owner's manual

Contents

Harman Kardon AVR430 Service Manual Manual pdf 15 page image

MAIN REMOTE CONTROL FUNCTIONSMemory Button: Press this button to enter aradio station to the AVR 630’s preset memory. First,tune the desired station, and then press this button.Within five seconds of when you see the station’sfrequency flash in the Upper Display Line # andin the on-screen display, press the numeric keysfor the preset number between 01 and 30 that youwish to assign to the station. (See page 34 for moreinformation.)Stereo Mode Select Button: Press this buttonto select a stereo listening mode. When the button ispressed so that SURROUND OFF appears inthe Lower Display Line $, the AVR will operate in abypass mode with true, fully analog, two-channelleft/right stereo mode with no surround processing orbass management, as opposed to other modes wheredigital processing is used. When the button is pressedso that SURROUND OFF appears in the LowerDisplay Line $, and the DSP and SURROUNDOFF Surround Mode Indicators % are lit, you willenjoy a two-channel presentation of the sound alongwith the benefits of bass management. Depending onwhether your system is configured for 5.1 or 6.1/7.1channels, the next press of the button will cause either5 CH STEREO or 7 CH STEREO toappear, and the stereo signal will be routed to all five(or seven) speakers. (See page 31 for more informa-tion on stereo playback modes.) DTS Neo:6 Mode Select Button: Press thisbutton to select a DTS Neo:6 mode. (See page 31for the available DTS Neo:6 options.) DTS Digital Mode Select Button: When aDTS-encoded digital source is playing, each press ofthis button will scroll through the available DTS modes.The specific choice of modes will vary according tothe type of encoding on the disc and your system’sspeaker configuration. When a DTS source is not inuse, this button has no function. (See page 31 for theavailable DTS digital options.) Dolby Mode Select Button: This button is usedto select from the available Dolby Surround modes.Each press of this button will select one of the DolbyPro Logic II modes or Dolby 3 Stereo. When a DolbyDigital-encoded source is in use, the Dolby Digitalmode may also be selected. (See page 31 for theavailable Dolby surround mode options.) 6-Channel/8-Channel Input Select: Press thisbutton to select the device connected to the 6- or 8-Channel Direct Inputs . (See page 29 for moreinformation.) SPL Select Button: This button activates theEzSet function to quickly and accurately calibrate theAVR 630’s output levels. When the button is pressedyou will then need to select between automatic EzSetoperation or using the remote as a manual SPL meterby pressing the ⁄/¤ Navigation Button o untilyour choice appears in the remote’s LCD display.Press the Set Button q to enter the setting, andthen follow the instructions as displayed in the LCDdisplay. (For complete information, see page 26.) EzSet Microphone Sensor: The microphonesensor that is used by the EzSet system is behind thethree slots at the top of the remote control. Whenusing EzSet to calibrate the AVR 630, be certain thatthe slots are not covered. (See page 26 for moreinformation on using EzSet.) Lens: The infrared emitters behind the plasticlens at the top of the remote communicate the remotecodes to the AVR 630. Be certain that the lens is notcovered when using the remote, and point the lenstoward the AVR for best results. In learning mode, theremote receives IR codes to be learned through asensor behind the lens.NOTE: DO NOT remove the rubber plug that is suppliedto cover the jack on the upper right side of the remote.The jack is not active and is reserved for future use.4014 MAIN REMOTE CONTROL FUNCTIONSAVR430/AVR630 harman/kardon15