Harman Kardon DVD 50 Owner's Manual

Also see for DVD 50: Brochure Brochure Specifications Service manual

Harman Kardon DVD 50 Owner's Manual Manual pdf 19 page image

19 SETUP MENUSetup MenuFigure 1To navigate through the settings on the screen,use the ⁄/ ¤ Navigation Buttons e toscroll up or down through the list of settings orthe list of options. Press the ‹/ › NavigationButtons e to move back and forth betweenthe list of settings of the left side of the screenand the list of options for those settings on theright side of the screen. To choose a specificoption, use the ⁄/ ¤ Navigation Buttonse until it is highlighted. Press the EnterButton ` to select the choice. When a selec-tion is made, you may confirm the choice bychecking to see that an orange dot fills thecircle next to the choice.Audio Language SelectionThe Audio Language option sets the defaultchoice for the language that will be playedfrom a DVD disc.To select the language default, you must beviewing the Setup Menu (Figure 1), which isavailable by pressing the Menu Buttonwhile the unit is in the Stop mode. AudioLanguage Selection is the first option, so it willautomatically be highlighted in dark blue whenthe Setup Menu is displayed.To change the default Language, press the ›Navigation Button e and note that the listof system defaults will be replaced with a list ofthe available options, for the audio languagesetting as shown in Figure 2. The current lan-guage choice will be indicated by a filled-inorange circle on the list on the right side ofthe screen.Figure 2To change the default setting, press the⁄/ ¤ Navigation Buttons e until thedesired choice is highlighted, and then pressthe Enter Button `. Note that the circle foryour choice will fill in, and the menu will returnto the default listings.If you wish to change the default to a languageother than those shown in the menu, press the¤ Navigation Button e until the “Other”line on the bottom is highlighted. Consult theLanguage Codes list on page 38 for the desiredlanguage. Press the Enter Button `. Next,enter the number for the desired language codeusing the ⁄/ ¤ Navigation Buttons e.Press the buttons until the desired numberappears in the first position, and then press the› Navigation Button e to move to thenext position. Continue to enter the numberusing the ⁄/ ¤ Navigation Buttons e ateach spot and then move to the next one.When all four digits have been entered and theOK box is highlighted, press the Enter Button` to store the selection in the DVD 50’smemory. Although the word “OTHER” willappear in the settings list, your desired choicewill be entered.Note that when a default language is selected,it will be used whenever that language is pres-ent on the DVD disc being played. However,when that language is not present, the lan-guage used will be the one preprogrammedinto the disc itself. (Typically, that default willbe English for discs sold in Region 1, but theselection may vary at the discretion of the disc’sproducer.)Although the default determines the languagethat will be used when a disc is first put intoplay, the language may easily be changed atany time through the use of the Menu Bar. Seepage 30 for more information.If you have no other changes to make after set-ting this default, press the Menu Buttonto remove the Setup Menu from the screen, orpress the Play Button g/# to begin orresume playback.Subtitle Language SelectionThe Subtitle Language option sets the defaultchoice for the language that will be displayedwhen subtitles are turned on during DVDplayback.To select the Subtitle Language default, youmust be viewing the Setup Menu (Figure 1),which is available by pressing the MenuButton while the unit is in the StopMode. At the Setup Menu, press the ¤Navigation Button e until the SubtitleLanguage option is highlighted.To change the default Subtitle Language, pressthe › Navigation Button e and note thatthe list of system defaults will be replaced witha list of the available options, as shown inFigure 3. The current subtitle language choicewill be indicated by a filled-in circle on the liston the right side of the screen.Figure 3To change the default setting, press the ⁄/ ¤Navigation Buttons e until the desiredchoice is highlighted, and then press the EnterButton `. Note that the circle for yourchoice will fill in, and the menu will return tothe default listings.If you wish to change the subtitle default to alanguage other than those shown, press the¤ Navigation Button e until the “Other”line on the bottom is highlighted. Consult theLanguage Codes list on page 38 for the desiredlanguage. Press the Enter Button `. Next,enter the number for the desired language codeusing the ⁄/ ¤ Navigation Buttons e.Press the buttons until the desired numberappears in the first position, and then press the› Navigation Button e to move to thenext position. Continue to enter the numberusing the ⁄/ ¤ Navigation Buttons e ateach spot and then move to the next one.When all four digits have been entered and theOK box is highlighted, press the Enter Button` to store the selection in the DVD 50’smemory. Although the word “OTHER” willappear in the settings list, your desired choicewill be entered.Note that when a default subtitle language isselected, it will be used whenever that lan-guage is present on the DVD disc being played.However, when that language is not present,the language used will be the one prepro-282828