Icom IC-F3262D series Instructions Manual

Also see for IC-F3262D series: Instructions

Icom IC-F3262D series Instructions Manual Manual pdf 1 page image

– 4 –– 1 –Thank you for choosing the IC-F3262DT/IC-F3262DSvhf dpmr handheld transceivers or IC-F4262DT/IC-F4262DS uhf dpmr handheld transceivers.READ ALL INSTRUCTIONS carefully andcompletely before using your transceiver.INSTRUCTIONSVHF dPMR HANDHELD TRANSCEIVERSIç-F4262D seriesUHF dPMR HANDHELD TRANSCEIVERSIç-F3262D seriesA-7213D-1EU Printed in Japan© 2015 Icom Inc.1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, JapanBattery pack Belt clipConnector cover(with screw)Flexible antenna(This illustration isfor the UHF type.)SUPPLIED ACCESSORIESThis instruction sheet includes some functions which areusable only when they are preset by your dealer. Ask yourdealer for details.See the operating guide for details of the IDAS™dPMR™ (digital Private Mobile Radio) and the BIIS(Binary Interchange of Information and Signaling) 1200system operations. Ask your dealer for details.FOREWORDIcom, Icom Inc. and Icom logo are registered trademarks of IcomIncorporated (Japan) in Japan, the United States, the United Kingdom,Germany, France, Spain, Russia, Australia, New Zealand, and/or othercountries.IDAS and the IDAS logo are trademark of Icom Incorporated (Japan).dPMR and the dPMR logo are trademarks of the dPMR MoU Association.All other products or brands are registered trademarks or trademarks of theirrespective holders.FUNCTION DISPLAYq SIGNAL STRENGTH ICONDisplays the relative receive signal strength.w LOW POWER ICONDisplayed when low output power is selected.• When the battery charge decreases to a specified level, lowpower is automatically selected.e SPEAKER/TELEPHONE ICONDisplayed when the channel is in the ‘audible’➥(unmute) mode.Displayed when a matched signal is received.➥“➥ ” is displayed when connecting to a telephone line.r SCRAMBLER ICONDisplayed when the Voice Scrambler function is ON.t SCAN ICONDisplayed while scanning.y MESSAGE ICONDisplayed when a received message (Short Data➥Message or Status Message) is stored in the stackmemory.Blinks when an unread message is in the stack➥memory.u BELL ICONDisplayed when a matched signal is received, dependingon the presetting.i GPS/COMPANDER ICON➥ Displayed when the GPS receiver acquires the GPSsignal from a satellite and the GPS Indicator is set toON.➥ “ ” is displayed when the Compander function isactivated and the GPS Indicator is set to OFF.o BATTERY ICONDisplays the battery level.IndicationBattery level Full Mid ChargingrequiredExhaustedBatteryblinks when the battery is over charged.blinks when the battery is exhausted.• This icon may not be displayed, depending on the presetting.!0 ALPHANUMERIC READOUT➥ Displays the operating channel number, channelname, Menu contents, DTMF code, and so on.➥ Depending on the presetting, characters are displayedin 1 line or 2 lines on the display.• In this instruction manual, the display illustration isdescribed as having characters displayed in 2 lines.!1 KEY ICONSDisplay the assigned function of the [P0], [P1], [P2] and[P3] front panel keys.001 ch-01IC-F3262DMENUPRIVATEID 0000002dPMR CLRMENUCALL00011234CALL MONTXCEBIISCLRq we rt y u i o!0!1About the LED indicatorD• Lights red while transmitting.• Lights green while receiving a signal, or whenthe squelch is open.• Blinks red when the battery is exhausted.About the Multi-connectorD CAUTION: Attach the connector coverwhen an optional accessory is not used.PANEL DESCRIPTIONTurning power OND Before using the transceiver for the first time, the batterypack must be fully charged for optimum life andoperation. See the back page of this sheet.Rotate [VOL] to turn ON the power.➥NOTE:• If the transceiver is programmed for a start uppassword, input the digit codes as directed by yourdealer.• The battery type must be selected, according to theattached battery type, when tuning the transceiver ON.See the operating guide for details of entering thepassword or selecting the battery type.BASIC OPERATIONReceiving and TransmittingDReceiving:Select a channel.qRotate [Rotary selector].➥Push [CH Up] or [CH Down].➥Push one of the direct channel select keys,➥[MR-CH 1] to [MR-CH 4].When receiving a call, rotate [VOL] to adjust the audiowoutput level to a comfortable listening level.Transmitting:CAUTION: Attach an antenna before transmitting.Transmitting without an antenna may damage thetransceiver.Wait until the channel is clear to avoid interference.While holding down [PTT], speak at a normal voice level.qRelease [PTT] to receive.wIMPORTANT:To maximize the readability of your signal:1. After pushing [PTT], pause briefly before you startspeaking.2. Hold the microphone 5 to 10 cm from your mouth, thenspeak at a normal voice level.*1 A GPS receiver is bult-in, depending on the transceiver version.* 2 Dealer assignableAntennaconnector[Rotary Selector][Emer]*[Side1]*[PTT][Side2]*[Side3]*10-keypad[P0]*2, [P1]*2,[P2]*2, [P3]*2Function displayMicrophoneSpeakerLED indicatorMulti-connector[VOL]GPS receiver*1The illustration is of the 10-key type transceivers.

/ 2

Related manuals for Icom IC-F3262D series