Icom IC-F7510 Instructions Manual

Also see for IC-F7510 Series: Operating guide Instructions

– 2 – – 3 –D About the Status indicator• Lights red while transmitting.• Lights green while receiving a signal, or when the squelchis open.PANEL DESCRIPTIOND About the Microphone connectorConnect the supplied or optional microphone.NEVER connect non-specifi ed microphones. The pinassignments may be different and may damage thetransceiver.Speaker[VOL]StatusindicatorMicrophoneconnectorFunctiondisplaydisplay [OK] [Emer][Emer][Up]/[Down][Right]/[Left][Back][P1] [P2] Power keyREAR PANEL CONNECTIONNOTE: Different functions may have been assigned to the keys by your dealer, except for the Power key.D Turning power ONPush [ ] to turn ON the transceiver.D Receiving and TransmittingReceiving:1. Push [Up] or [Down] to select a channel.2. When receiving a call, rotate [VOL] to adjust the audiooutput level to a comfortable listening level.Transmitting:1. Wait until the channel is clear to avoid interference.2. While holding down [PTT], speak at your normal voicelevel.3. Release [PTT] to receive.BASIC OPERATIONOPTIONS• RMK-5 SEPARATION KIT + separation cable* 1Enables you to separately install the transceiver’s mainunit from the front panel for convenient operation.• HM-218 HAND MICROPHONE + separation cable* 2Command microphone with a built-in speaker You need the RMK-5 to connect the HM-218 to the transceiver.• RMK-7 DUAL HEAD KIT + separation cable* 1Enables you to connect two control heads to thetransceiver’s main unit for dual head operation.*1 OPC-2364, OPC-2365, OPC-2366 or OPC-2367 SEPARATIONCABLE is used to connect between the control head and thetransceiver’s main unit.• OPC-2364: 1.9 m / 6.3 ft • OPC-2365: 3 m / 9.9 ft• OPC-2366: 5 m / 16.4 ft • OPC-2367: 8 m / 26.3 ft* 2 OPC-2373 or OPC-2374 SEPARATION CABLE for commandmicrophone is used to connect between the HM-218 and RMK-5.• OPC-2373: 1.9 m / 6.3 ft • OPC-2374: 8 m / 26.3 ft• SP-30, SP-35, SP-35L EXTERNAL SPEAKERSInput impedence: 4 ΩSP-30: Rated input= 20 W, Maximum input = 30 WSP-35/SP35L: Rated input= 5 W, Maximum input = 7 W• HM-220, HM-220T, HM-221, HM-221T HAND MICROPHONESHM-220: Self-grounding heavy duty microphoneHM-220T: Self-grounding heavy duty DTMF microphoneHM-221: Hand microphoneHM-221T: DTMF microphone• SM-29 DESKTOP MICROPHONE• UX-241 GPS ANTENNAEnables you to use the GPS function.• VS-3 Bluetooth ® HEADSETThe Bluetooth ® headset with a [PTT] switch.IMPORTANT:To maximize the readability of your signal:1. After pushing [PTT], pause briefly before you startspeaking.2. Hold the microphone 5 ~ 10 cm (2 ~ 4 inches) from yourmouth, then speak at your normal voice level.• About the third party Bluetooth® headsets:Icom has checked the PTT operation with some 3M Peltorheadsets such as the WS Headset XP, WS ProTac XP andWS Alert XP. (Compatibility not guaranteed.)Antenna12 VBatteryqerutSolderCrimpNOTE: Use the terminals as shownbelow for the cable connections.wBlackRedyANTENNA CONNECTORConnect to an antenna. Contactyour dealer about antenna selectionand placement.qwD-Sub 25-pinConnects to an external unit.tGPS ANTENNA CONNECTORConnect the UX-241 GPS antenna.eIGNITION LEADConnects to an ignition line.Do not put pressure on thislead. Binding to the DC powercable is recommended.u MICROPHONE HANGERFor a self-grounding type:The microphone ON/OFF hook functionscan be used without the vehicle’s ground.For a non-self-grounding type:Connect the microphone hanger to thevehicle’s ground for microphone ON/OFFhook functions.rConnects to a 12 V DC battery.Pay attention to polarities. NEVER connectto a 24 V battery.This will damage the transceiver.iiEXTERNAL SPEAKER JACKConnect a 4 ~ 8 Ω external speaker.RR WARNING! NEVERremove the fuseholders from the DCpower cable.y USB (Micro-B) CABLEConnects to a PC.Fuse holdersNon-self-grounding typeSelf-grounding typeUser supplied

/ 2

Related manuals for Icom IC-F7510 Series