Icom ID-51E User Manual

Also see for ID-51A: Manual Manual Basic instructions Brochure & specs Basic instructions

Contents

Icom ID-51E User Manual Manual pdf 29 page image

5 - 115-3 TRANSMIT ADJUSTMENT (Continued)5-4 RECEIVE ADJUSTMENTS1) Select an adjustment item (band) using / .2) Set the SSG as specifi ed (frequency, deviation and output level), and then push to automatically adjust.ADJUSTMENT ADJUSTMENTITEM OPERATION VALUERECEIVESENSITIVITY[A-BAND]NOTE: “RECEIVE SENSITIVITY” must be adjusted before “S-METER.” Otherwise, “S-METER” willnot be adjusted properly.– 1 1) Set the power supply voltage to 7.4 V.2) Connect an SSG to the antenna connector, and then set it as;Frequency : (Displayed on the function display)Level : –10 dBμ (–117 dBm)†Modulation : 1 kHzDeviation : 3.5 kHz–(137.02 MHz) [VTL] 2Push .(Automaticadjustment)(145.02 MHz) [VTM] 3(173.98 MHz) [VTH] 4(380.02 MHz) [UTL] 5(435.02 MHz) [UTM] 6(478.98 MHz) [UTH] 7[AIR BAND] – 1 1) Set the power supply voltage to 7.4 V.2) Connect an SSG to the antenna connector, and then set it as;Frequency : (Displayed on the function display)Level : –10 dBμ (–117 dBm)†Modulation : 1 kHzDeviation : 30% (AM)–(108.02 MHz) [ATL] 2 Push .(Automaticadjustment)(127.02 MHz) [ATM] 3(136.95 MHz) [ATH] 4[B-BAND] – 1 1) Set the power supply voltage to 7.4 V.2) Connect an SSG to the antenna connector, and then set it as;Frequency : (Displayed on the function display)Level : –10 dBμ (–117 dBm)†Modulation : 1 kHzDeviation : 3.5 kHz–(137.02 MHz) [VTL]Push .(Automaticadjustment)(145.02 MHz) [VTM] 2(173.98 MHz) [VTH] 3(380.02 MHz) [UTL] 4(435.02 MHz) [UTM] 5(478.98 MHz) [UTH] 6S-METER[BC BAND]NOTE: “RECEIVE SENSITIVITY” must be adjusted before “S-METER” and “S-METER S3 LEVEL.” Other-wise, “S-METER” and “S-METER S3 LEVEL will not be adjusted properly.–1 1) Set the power supply voltage to 7.4 V.2) Connect an SSG to the antenna connector and set it as;Modulation : 1 kHzDeviation : 30% (AM)–(AM S0 level)[BS0]2 • Set the SSG as;Frequency : (Displayed on the function display)Level : +2 dBμ (–105 dBm)†Push .(Automaticadjustment)(AM S3 level) [BS3] 3 • Set the SSG as;Level : +5 dBμ (–102 dBm)†(AM Full scale)[BSF]4 • Set the SSG as;Frequency : (Displayed on the function display)Level : +12 dBμ (–95 dBm)†(WFM S0 level)[BS0]5 • Set the SSG as;Frequency : (Displayed on the function display)Level : +2 dBμ (–105 dBm)†(WFM S3 level)[BS3]6 • Set the SSG as;Frequency : (Displayed on the function display)Level : +5 dBμ (–102 dBm)†(WFM Full scale)[BSF]7 • Set the SSG as;Frequency : (Displayed on the function display)Level : +12 dBμ (–95 dBm)††; This output level of a standard signal generator (SSG) is indicated as SSG’s open circuit.