JBL Cinema Vision CVPD50 Quick Start Manual

Also see for CINEMA VISION CVR700: Owner's guide Service manual

®Thank you for purchasing a JBL Cinema Vision ™ System. This Quick-StartGuide will help you with a basic system installation. For detailed informationon any step, please refer to the Owner’s Manual. We strongly recommendthat you read the two Owner’s Manuals for the loudspeakers and for theCVR700/CVPD50 for complete details on how to install, configure andoperate the JBL Cinema Vision System, as well as for the important safetyinformation they contain.FIGURE 1 – SPEAKERPLACEMENTThe colors shown for each speaker correspond tothe matching output terminal connection on theback of the CVR700.FRONTLEFTSPEAKER(White)BACK†SURROUNDLEFTSPEAKER(Brown)BACK†SURROUNDRIGHTSPEAKER(Tan)CENTERSPEAKER(Green)SUBWOOFER(Purple)SIDESURROUNDLEFTSPEAKER(Blue)FRONTRIGHTSPEAKER(Red)SIDESURROUNDRIGHTSPEAKER(Gray)Step 1. Install the CVPD50 plasma screen and place yourspeakers in the listening room. See the owner’s manualfor instructions on assembling the credenza stand for theCVPD50 screen or for wall-mounting; see the CVSAT50owner’s manual for instructions on assembling theCVTS50 table stands or for wall-mounting. TheCVSAT50 speakers may be mounted in-wall using theoptional CVIW50 in-wall adaptors and CVRIF50 rough-inframes.Proceed to Step 2 on back cover.SPEAKER PLACEMENTJBL CINEMA VISION™ SYSTEMQUICK-START GUIDECONNECTIONS COLORGUIDEAudio Connections Left RightFrontCenterSide SurroundSubwooferBack SurroundDigital Audio ConnectionsCoaxialOpticalVideo ConnectionsCompositeS-VideoMatch the colored jacks on the CVR700 to the appropriatejacks on your source equipment or speakers. The colors arestandardized, but not all equipment or connectors use them.PRO CINEMACOMES HOME ™Step 2. Connect the speakers to the receiver: red (+) on speaker to colored (+) on receiver, and black (–) to black (–).Step 3. Connect the Subwoofer Pre-Out jack to the Line-In jack on your subwoofer. You may adjust the settings on the subwoofer later as needed.Step 4. Connect AM and FM antennas (Fig. 2).Step 5. Optional Connection of External Components – See inside spread.Step 6. Final Connection Sequence: First – Plug CVPD50 and CVR700 power cords (and external components’ cords, if any) into AC power outlets. Use a mirror to locate connectors on underside of CVPD50. Second – Turn on CVPD50master power switch (“1” position; depressed toward rear of unit). Make sure CVR700 is in Standby mode – power LED red. Third –Last step is to connect JBL Digital Link ™ cable from CVR700 output to port on underside of CVPD50.Do notconnect this output port to any device other than the JBL Cinema Vision CVPD50 screen.You have now completed a basic installation of the JBL Cinema Vision System. After a few configuration adjustments, described in Steps 7 through 11 on the inside spread, you’ll be ready to enjoy the finest in home theater entertainment!Notes:1. Press and hold for 2 seconds and release the Power On button to turn on all devices programmed into the remote; press and hold the Power Off button to turn all of these devices off.2. Press and hold for 2 seconds and release any Source Input selector on the remote to turn on the CVR700, CVPD50 and source device, to select the source, and to begin playing the last disc, tape or television channel.3. For external sources, or when Autosize is off, press the Letterbox button repeatedly to scroll through applicable video-display options (with or without black bars, scaling, aspect ratio). Press the Frame button to scroll through all options.BACK SURROUND(7.1 SYSTEM ONLY)RIGHT SPEAKERBACK SURROUND(7.1 SYSTEM ONLY)LEFT SPEAKERFRONT RIGHTSPEAKERFRONT LEFTSPEAKERCENTERSPEAKERSUBWOOFER+ _ + _ LINE IN/SUB/LFE+ _SURROUND (5.1 SYSTEM)SIDE SURROUND (7.1 SYSTEM)RIGHT SPEAKER+ _ + _ + _SURROUND (5.1 SYSTEM)SIDE SURROUND (7.1 SYSTEM)LEFT SPEAKER+ _AM AntennaCVPD50FM AntennaFIGURE 2 – SPEAKER AND SYSTEM CONNECTIONSFIGURE 3 – HOW TO USETHE BINDING-POSTSPEAKER TERMINAL®JBL CINEMA VISION™ SYSTEMQUICK-START GUIDEPRO CINEMACOMES HOME ™250 Crossways Park Drive, Woodbury, New York 11797 www.jbl.com © 2004 Harman International Industries, Incorporated Part No. CQE1Aaa243Z†Alternate positions for surroundspeakers in a 5.1 system; required positionsfor back surround speakers in a 7.1 system.JBL Digital Link™Important: Plug in last,after AC power. SeeStep 5.

/ 2

Related manuals for JBL CINEMA VISION CVR700