JBL VLA-C SERIES User Manual

28COMPPAMTvaPriblir| USER’S GUIDEVLA-C2100Two-Way Full Range Dual 10” Array ModuleSystem:Frequency Range (-10 dB)1: 86 Hz - 18 kHzFrequency Response (±3 dB)1: 109 Hz – 15.3 kHzSystem Power Rating2: Full Range: 800 W Continuous Pink Noise (3200 W peak), 2 hrs400 W Continuous Pink Noise (1600W peak), 100 hrsBi-amp LF: 800 W Continuous Pink Noise (3200 W peak), 2 hrs400 W Continuous Pink Noise (1600W peak), 100 hrsBi-amp HF: 150 W Continuous Pink Noise (600 W peak), 2 hrs50 W Continuous Pink Noise (200 W peak), 100 hrsMaximum Input Voltage: Full-Range: 80 V Rms (2 hrs), 160 V peakBi-Amp LF: 80 V Rms (2 hrs), 160 V peakBi-Amp HF: 50 V Rms (2 hrs), 135 V peakMaximum SPL (1m)3: 131 dB Cont. Ave (2 hrs), 137 dB PeakSensitivity4: Full-Range: 102 dB (85 Hz – 19 kHz)Bi-Amp LF: 100 dB (85 Hz – 950 Hz)Bi-Amp HF: 107 dB (950 Hz – 19.2 kHz)Coverage Pattern (-6 dB): Horizontal: 100° (+5°/-15°, 1.5 kHz to 15 kHz)Vertical: Varies with array size and configurationImpedance: Full-Range: 8Ω, 6.7Ω min @ 200 HzBi-Amp LF: 8Ω, 6.9 Ω min @ 230 HzBi-Amp HF: 16 Ω, 15.9 Ω min @ 1.1 kHzAmplifiers: Crown DCi Family with DSP on-boardRecommended: Crown DCi 2 | 1250NCrown DCi 4 | 1250N/ND/DACrown DCi 2 | 2400NCrown DCi 4 | 2400NTransducers:Low Frequency Driver:High Frequency Driver:2 x 2261FF, 254 mm (10 in) diameter, each with two 76 mm (3 in) diameter voice coils, Neodymium DifferentialDrive®, Direct Cooled™3 x 2415K, D2 Dual Diaphragm Dual Voice Coil Compression Drivers, each with two 38 mm (1.5 in) dia. Voice Coils; 21mm (0.8 in) exitPhysical:Enclosure Material: Fiberglass shell, gelcoat finish, with 18 mm Birch plywood internal bracing.Grille: Powder coated 14 gauge hex-perforated steel with zinc under-coating, backed with acoustically transparent clothand hydrophobic screen.Inter-Enclosure Angles: VLA-C2100 to VLA-C2100: 2.4°, 3.8°, 6.0°, 9.5°, 15° using VLA-C2100 Bracket Plate (included with VLA-C2100)VLA-C2100 to VLA-C265 (either model on top/bottom): 1.9°, 3.0° using VLA-C2100 Bracket Plate (included withVLA-C2100) and 4.7°, 7.5°, 11.9° using VLA-C265 Bracket Plate (included with VLA-C265)VLA-C2100 below VLA-C125S Subwoofer (VLA-C2100 cannot be connected above C125S): 0°, 7.5° using VLA-C125SBracket Plate (included with VLA-C125S)Environmental: IP-55 rating per IEC529 (dust protected and protected against jets of water).Terminals: CE-compliant covered barrier strip terminals. Barrier terminals accept up to 5.2 sq mm (10 AWG) wire or max width9mm (0.375 in) spade lugs. Touch-proof covers.Colors: -GR: Gray (similar to Pantone 428C), -BK: BlackDimensions (H x W x D): 381 x 848 x 460 mm (15.0 x 33.4 x 18.1 in)Net Weight (ea): 37.7 kg (83 lbs)Shipping Weight (ea): 44.0 kg (97 lbs)Included Accessories: 2 x VLA-C2100 Bracket Plates8 pcs. M10 x 35 mm stainless steel bolts (1.5mm pitch, 6 mm hex-drive) for attaching Bracket Plates2 pcs. Plastic Trim Cover Panels for Bracket Plates, each attaches via4 pcs (8 total) 3-32 x ½” trusshead, phillips-drive, stainless steel bolts.Optional Accessories: VLA-C-SB Suspension Bar Kit for the array, includes 2 identical Suspension Bars (for top/bottom), 4 pcs ¾-inch Class2 Screw Pin Shackles (must use 2 Shackles for each Suspension Bar, located at end channels, not in the center).1. Using recommended DSP tuning, full-space (4π)2. Continuous Pink Noise rating is IEC-shaped pink noise with 6 dB crest factor. Peak defined as 6 dB above Continuous Pink Noise Rating.3. Continuous Average calculated from sensitivity and power handling, exclusive of power compression. Peak measured, unweighted SPL, bi-amp mode,measured under full-space conditions at 1 meter using broadband pink noise with a 12 dB crest factor and specified preset.4. 2.83 V RMS, full-space (4π)JBL continually engages in research related to product improvement. Some materials, production methods and design refinements are introduced intoexisting products without notice as a routine expression of that philosophy. For this reason, any current JBL product may differ in some respect from itspublished description, but will always equal or exceed the original design specifications unless otherwise stated.