Jacuzzi Comfort Plus Bath Series Installation And Operating Instructions Manual

Also see for AMIGA PLUS: Installation and operation instructions Manual

Contents

Jacuzzi Comfort Plus Bath Series Installation And Operating Instructions Manual Manual pdf 15 page image

ENGLISHOperationNote: These instructions pertain to all bath products manufac-tured by Jacuzzi Whirlpool Bath. Not all features discussed inthis instruction pamphlet apply to all baths.All baths manufactured by Jacuzzi Whirlpool Bath © are designedfor "fill and drain," which means the bath should be drained aftereach use and filled with fresh water by the next bather. This is ahealth precaution, as these baths are not designed to hold watercontinuously like pools or spas.OPERATING INSTRUCTIONS1"FILL TO AT LEAST1" ABOVE HIGHEST JET9Jacuzzi Whirlpool Bath © BP43000 2/05Control PanelComfort Plus No Light SystemThe Comfort Plus control panel, located on the bath, allows you tocontrol the pump and observe the water temperature while in thebath. During operation the system displays water temperatureallowing for an approximate temperature fill. The system (pump,heater, and display) automatically shuts off after 30 minutes ofoperation. To restart simply press the ON/OFF button again.CAUTION: Temperature sensors and values are approximate andmay vary. Use caution when entering heated water.On/Off Pump/MotorPressing this button will turn ON the pump/motor. Pressing a sec-ond time will turn OFF the pump/motor.LED DisplayThe Comfort Plus control panel water temperature displays whenthe water level covers the internal water sensor even if the ComfortPlus No Light System controls are not turned ON. This feature isdesigned to give a temperature indication even if the whirlpool systemis not being used.Pressing and holding the ON/OFF button for three (3) secondsdisplays a "time remaining" minute countdown. After displaying the"time remaining" countdown for 30 seconds, the readout reverts backto the temperature display.Control PanelComfort Plus With Light SystemThe Comfort Plus With Light System control panel, located on thebath, allows you to control the pump, observe the water temperature,and control the Chromotherapy lighting system while in the bath.During operation the system displays water temperature allowing foran approximate temperature fill. The Chromotherapy lighting systemcontrols the 2 Channel Chromotherapy lamps where you can turn onbath lighting in white, a color of choice, or a continuous flow throughall colors. The system (pump, heater, and display) automaticallyshuts off after 30 minutes of operation, the Chromotherapy lightingsystem has a 4 hour lamp timeout. To restart the system (pump,heater, and display) simply press the ON/OFF button again.CAUTION: Temperature sensors and values are approximate andmay vary. Use caution when entering heated water.On/Off Pump/MotorPressing this button will turn ON the pump/motor. Pressing a sec-ond time will turn OFF the pump/motor.Bath Light ON/OFFPressing this button will turn ON the bath light(s). The light(s) willcome ON displaying the White colored light. Pressing a secondtime will turn all light(s) OFF. (Use the "Light Color Cycle" button toturn ON the color lights.)Light Color CyclePressing this button will turn ON the colored light(s) to the "favorite"light (default is blue). Pressing this button again will begin the light(s)cycling through each of the available colors. This will continue untilthe Light Color Cycle button is pushed again, which stops the lightcycling action on the current color. Press the button again and youwill begin the Light Color Cycle again.To create a new “favorite” color: Allow the lights to rotate to the new"favorite" light color. Stop the cycling on that color. Press and holddown the button for three seconds (the light will then blink to confirmthe new "favorite").LED DisplayThe Comfort Plus control panel water temperature displays whenthe water level covers the internal water sensor even if the ComfortPlus With Light System controls are not turned ON. This feature isdesigned to give a temperature indication even if the whirlpool systemis not being used.Pressing and holding the ON/OFF button for three (3) secondsdisplays a "time remaining" minute countdown. After displaying the"time remaining" countdown for 30 seconds, the readout reverts backto the temperature display.Water LevelClose the drain and fill the bath until water is at least 1" above thehighest jet (see water line indicated in the illustration). Do not turnon the whirlpool system at any time if the jets are not completelyimmersed in water. Running the whirlpool system when there isinsufficient water in the bath could result in water spraying outsidethe bath area. Running the whirlpool system without water will dam-age the recirculating pump.Do not immerse the control panel by overfilling the bath.101101ON/OFFPUMP MOTORLED DISPLAY101101ON/OFFPUMP MOTOR BATH LIGHT ON/OFFLIGHT COLOR CYCLELED DISPLAY