Jacuzzi LED Series Manual

Also see for J - 210: Owner's manual Owner's manual Owner's manual Owner's manual Owner's manual

Contents

Jacuzzi LED Series Manual Manual pdf 13 page image

94.4 Programming Filter Cycles (2011-2012 J200 models equipped with a circulationpump)To select a pre-programmed filter cycle or lockout mode, press and hold both control panelWARMER and COOLER buttons at the same time, then release. Then press either WARMER orCOOLER buttons to select either filter mode F0 through L2 below:Standard ModeF0 5 minutes of filtration per day (one 5 minute “Blow-Out” cycle every 24 hours to purge all plumbing lines.F1 1 hour of filtration per day (one 30-minute cycle every 12 hours); this is the factory default setting.F2 1.5 hours of filtration per day (one 30-minute cycle every 8 hours).F3 2 hours of filtration per day (one 30-minute cycle every 6 hours).Economy ModeF4 1 hour of filtration/heating per day (one 30-minute cycle every 12 hours).F5 1.5 hours of filtration/heating per day (one 30-minute cycle every 8 hours).F6 2 hours of filtration/heating per day (one 30-minute cycle every 6 hours).Lock ModeL1 Lock Out (disables all hot tub functions to permit filter cleaning) - If hot tub is heating when the system isput into lockout mode, the heater will immediately turn off and the pump will cycle water for 30 seconds tocool heater element, then turn off.L2 Lock Mode (disables the jets and light buttons to prevent unauthorized use of the hot tub) - filter cycles andheater will continue to operation as programmed in this mode. The temperature display flashes when thisfunction is enabled. Example: The “F3” filter cycle was enabled prior to choosing lock mode. The hot tubcontinues to perform filter cycle “F3” until lock mode is canceled, allowing another filter cycle to be selected.4.5 Programming Filter Cycles (2013+ J200 models not equipped with a circulationpump)To select a pre-programmed filter cycle or lockout mode, press and hold both control panelWARMER and COOLER buttons at the same time, then release. Then press either WARMER orCOOLER buttons to select either filter mode F1 through L2 below:Standard ModeF1 4 hours of filtration a day (2 hour cycle every 12 hours): this is the factory default setting.F2 6 hours of filtration a day (2 hour cycle every 8 hours)F3 8 hours of filtration a day (2 hour cycle every 6 hours)Economy ModeF4 4 hours of filtration a day (2 hour cycle every 12 hours)F5 6 hours of filtration a day (2 hour cycle every 8 hours)F6 8 hours of filtration a day (2 hour cycle every 6 hours)Lock ModeL1 Lock Out (disables all hot tub functions to permit filter cleaning).Note: The spa should not be left in this lock mode for an extended period of time. Especially in colder climatesor when freezing conditions exist.L2 Lock Mode (disables the jets buttons to prevent unauthorized use of the hot tub) filtration/heating cyclesand heater will continue to operation as programmed in this mode. The temperature display flasheswhen this function is enabled. Example: The “F3” filter cycle was enabled prior to choosing lock mode.The hot tub continues to perform filter cycle “F3” until lock mode is canceled, allowing another filtercycle to be selected.L3* Lock Mode (disables the temperature up and down buttons to prevent unauthorized temperatureadjustments). Filtration/heating cycle will continue to operate as programmed in this mode. The jets andlights buttons will still continue to operate as normal. The temperature display flashes when this functionis enabled. *Due to a difference in software this feature is not available for all models, started in 2014.Note: To exit a Lock Mode you will need to re-enter the filtration/heating modes and select a cycle from F0-F6.