Jenn-Air 720-0063-LP Instructions Manual

Also see for 720-0063-LP: User manual

Contents

Jenn-Air 720-0063-LP Instructions Manual Manual pdf 12 page image

GAS HOOK-UPOnly the pressure regulator and hose assemblysupplied with the grill should be used. Anyreplacement pressure regulator and hose assemblymust be specified by the grill manufacturer.This is a liquid propane configured grill.Do not attempt to use a natural gas supply unlessthe grill has been pre-configured for natural gasuse.Total gas consumption (per hour) of 720-0063-LPgrill with all burners on “HI”:Main burners 60,000 Btu/hr.Rotisserie burner 12,000 Btu/hrSide burner 12,000 Btu/hr.Total 84,000 Btu/hr.The installation of this appliance must conform withlocal codes or, in the absence of local codes, withthe national fuel gas code, ANSI Z223.1 Installationin Canada must be in accordance with the StandardCAN/CG A-B149.2 (installation code for gasburning appliances and equipment) and localcodes.LP Gas Cylinder Requirements (20lb. Cylinder)A dented or rusty LP Gas Cylinder may behazardous and should be checked by your LPsupplier. Never use a cylinder with a damagedvalve. The LP gas cylinder must be constructed andmarked in accordance with the specifications for LPgas cylinders of the U.S. Department ofTransportation (DOT), or the National Standard ofCanada, CAN/CSA-B339, Cylinders, Spheres andTubes for Transportation of Dangerous Goods; andCommission.The 20lb. cylinder must be provided with a shut offvalve terminating in an LP gas supply cylinder valveoutlet specified, as applicable, for connection typeQCC1 is the standard for compressed gas cylindervalve outlet and inlet connection ANSI/CGA-V-1.The cylinder supply system must be arranged forvapor withdrawal. The cylinder must include a collarto protect the cylinder valve.Manifold pressure: (operating): 10” water column(W.C.), (non-operating): 11.2” water column (W.C.).LP Gas Cylinder must be fitted with OverfillProtection Device (OPD).LP GAS HOOK-UP:Ensure that the black plastic grommets on the LPcylinder valve are in place and that the hose doesnot come into contact with the grease tray or thegrill head.CONNECTION:Your grill is equipped with gas supply orifices foruse only with liquid propane gas. It is also equippedwith a high capacity hose/regulator assembly forconnection to a standard 20lb. LP cylinder (18-1/4”high, 12-1/4” diameter).To connect the L.P. gas supply cylinder:1. Make sure tank valve is in its full off position(turn clockwise to stop).2. Check tank valve to ensure it has properexternal male threads (type 1 connection perANSIZ21.81).3. Make sure all burner valves are in the offposition.4. Inspect valve connections, port and regulatorassembly. Look for any damage or debris.Remove any debris. Inspect hose for damage.Never attempt to use damaged or obstructedequipment. See your local LP gas dealer forrepair.5. When connecting regulator assembly to thevalve, hand tighten the nut clockwise to acomplete stop. Do not use a wrench to tighten.Use of a wrench may damage the quickcoupling nut and result in a hazardouscondition.6. Open the tank valve fully (counterclockwise).Use a soapy water solution to check allconnections for leaks before attempting to lightthe grill. See below. If a leak is found, turn thetank valve off and do not use the grill until alocal LP gas dealer can make repairs.To disconnect LP gas cylinder:1. Turn the burner valves off.2. Turn the tank valve off fully (turn clockwise tostop).3. Detach the regulator assembly from the tankvalve by turning the quick coupling nutcounterclockwise.10