Jenn-Air JEC4530YB00 Use & Care Manual

Also see for JEC4530YB00: Installation instructions

Contents

Heavy soil, dark streaks, specks and discoloration• Cooktop Polishing Creme or nonabrasive cleanser:Rub product into soil with a damp paper towel or soft cloth.Continue rubbing until white film disappears.Burned-on soil• Cooktop Polishing Creme and Cooktop Scraper:Rub creme into soil with damp paper towel. Hold scraper asflat as possible on surface and scrape. Repeat for stubbornspots. Polish entire cooktop with creme and paper towel.Metal marks from aluminum and copper• Cooktop Polishing Creme:Clean as soon as cooktop has cooled down. Rub creme intosurface with a damp paper towel or soft cloth. Continuerubbing until white film disappears. The marks will not totallydisappear but after many cleanings become less noticeable.Tiny scratches and abrasions• Cooktop Polishing Creme:Rub creme into surface with a damp paper towel or softcloth. Continue rubbing until white film disappears. Scratchesand abrasions do not affect cooking performance and aftermany cleanings become less noticeable.Do not use steel wool, abrasive powder cleansers, chlorinebleach, rust remover or ammonia because damage may occur.TROUBLESHOOTINGTry the solutions suggested here first in order to avoid the cost of an unnecessary service call.[] ...... []Nothing will operate r_q CZ3 ....r_qHas a household fuse blown, or has a circuit breakertripped?Replace the fuse or reset the circuit breaker. If the problemcontinues, call an electrician. [] , ..... []• Is the cooktop wired properly? I_ s_,t',o_o ,,_ko_See Installation Instructions. _ _ I_Cooktop will not operateIs the "All Off" cooktop lockout set?See "All Off/Lock" sectionIs the cooktop beeping continuously?Wipe debris from the control panel surface.Has one or more burners stopped working during use?Allow the cooktop to cool down for 30 minutes then turn theburner on again.Excessive heat around cookware on cooktop• Is the cookware the proper size?Use cookware about the same size as the surface cookingarea, element or surface burner. Cookware should not extendmore than 1/2"(1.3 cm) outside the cooking area.• Do cooktop surfaces become hot?REMEMBER: When cooktop is in use, the entire cooktoparea may become hot.Cooktop has flashing lights• Are the lights on the cooktop flashing on and off?All cooktop control panel lights flash on and off, indicatingthat one or more keys are permanently pressed.w_-,,• I_ . . I_ • o7o,_ •s 4 s e 7 a 9 loAll cooktop control panel lights OffFollow the steps below.1. Make sure the cooktop controls are OFE2. Clean the cooktop touch control panel thoroughly. See"General Cleaning" section.3. If the cooktop lights continue to flash, disconnect poweror unplug the cooktop.4. After 1 minute, reconnect power or plug in the cooktop.5. If the lights continue to blink on and off, call for service.Cooktop cooking results not what expectedIs the proper cookware being used?See "Cookware" section.Is the appliance level?Level the appliance. See the Installation Instructions.Does it appear to take longer to cook food at a certainpower level than usual, or some power levels do notperform as well as usual?The cooktop regulates the temperature of the internalcomponents and automatically reduces the power of all theelements in use without any visual or audible feedback. Allowthe cooktop to cool down for 30 minutes to resume normalcooking performance. See "To Use" in the "CooktopControls" section.E_A3 CZB EZB] ,,,to,., ,.,,,,,ot _t t _t []• IZC] • ,I_C] •2 3 4 S 6 7 a 9 _oAll cooktop control panel lights On