4Cabinet DimensionsNOTES: After making the countertop cutout, some installationsmay require notching down the base cabinet side walls to clearthe cooktop base. To avoid this modification, use a base cabinetwith sidewalls wider than the cutout.■ A minimum side clearance of 6" (15.2 cm) is recommendedbetween side of cooktop and side wall for maximumventilation performance.■ A minimum clearance of 2" (5.1 cm) is recommendedbetween the motor/blower and cabinet for proper cooling. A6" (15.2 cm) clearance is recommended for servicing access.Cutout DimensionsVenting RequirementsIMPORTANT: This cooktop must be exhausted outdoors unlessusing the Jenn-Air ® Duct Free Filter Accessory Kit. See “VentingMethods” section.■ Do not terminate the vent system in an attic or other enclosedarea.■ Use a Jenn-Air® vent cap.■ Vent system must terminate to the outside.■ Use only a 6" (15.2 cm) round metal vent. Rigid metal vent isrecommended. For best performance, do not use plastic ormetal foil vent.■ Before making cutouts, make sure there is proper clearancewithin the wall or floor for the exhaust vent.■ Do not cut a joist or stud unless absolutely necessary. If ajoist or stud must be cut, then a supporting frame must beconstructed.■ The size of the vent should be uniform.■ The vent system must have a damper. If roof or wall cap has adamper, do not use damper supplied with the range hood.■ Use vent clamps to seal all joints in the vent system.■ Use caulking to seal exterior wall or roof opening around thecap.■ Determine which venting method is best for your application.A. 30" (76.2 cm) on 30" (76.2 cm) models36" (91.4 cm) on 36" (91.4 cm) modelsB. Combustible area above countertop (shown by dashed box above)C. 30" (76.2 cm) minimum clearance between top of cooktop platformand bottom of uncovered wood or metal cabinet (24" [61 cm]minimum clearance if bottom of wood or metal cabinet is coveredby not less than¹⁄₄" [0.6 cm] flame retardant millboard covered withnot less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainlesssteel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)D. 13" (33 cm) recommended upper cabinet depthE. 2" (5.1 cm)F. 21¹⁄₈" (73.4 cm)G. 18" (45.7 cm) minimum clearance from upper cabinet to countertopwithin minimum horizontal clearances to cooktopH. Junction box or outlet; 12" (30.5 cm) minimum from bottom ofcountertopI. Junction box or outlet; 10" (25.4 cm) from right-hand side ofcabinetJ. 28⁷⁄₈" (73.4 cm) on 30" (76.2 cm) models34½" (87.6 cm) on 36" (91.4 cm) modelsK. 2½" (6.4 cm) minimum distance to nearest left and right sidecombustible surface above cooktopL. 1½" (3.8 cm) minimum clearance between back wall andcountertopDAEIJKGHLCFBA. 28⁷⁄₈" (73.4 cm) maximum on 30" (76.2 cm) models34½" (87.6 cm) maximum on 36" (91.4 cm) modelsB. 21¹⁄₈" (53.7 cm) maximum on both 30" (76.2 cm) and 36" (91.4 cm)modelsC. 8⁵⁄₈" (21.9 cm) on 30" (76.2 cm) models15⁷⁄₁₆" (39.2 cm) on 36" (91.4 cm) modelsD. 6⁵⁄₁₆" (16.0 cm) on both 30" (76.2 cm) and 36" (91.4 cm) modelsE. 2" (5.1 cm) minimum space to front edge of cooktopF. Floor exhaust optionG. 6¹⁄₈" (15.6 cm) for 6" (15.2 cm) vent systemH. 8⁵⁄₈" (21.9 cm) on 30" (76.2 cm) models15⁷⁄₁₆" (39.2 cm) on 36" (91.4 cm) modelsI. 16" (40.6 cm) on both 30" (76.2 cm) and 36" (91.4 cm) modelsJ. Wall exhaust optionABCDEFGHIJ