Jenn-Air JS42SEDUDW Installation Manual

Also see for JS42SEDUDW: Design and planning guide

Contents

Jenn-Air JS42SEDUDW Installation Manual Manual pdf 11 page image

112. Place pieces of the shipping carton on the floor when rollingthe dolly and refrigerator into the house. Move the refrigeratorclose to the built-in opening.3. Place top of cardboard carton or plywood under refrigerator.4. Stand the refrigerator up. First, place the left bottom edge ofthe refrigerator on the floor, stand the refrigerator upright andthen lower the right-hand side of the refrigerator to the floor.5. Reassemble the trim and top grille after the dolly has beenremoved from the refrigerator.Install Anti-Tip BoardsIMPORTANT:■ To avoid tipping during use, the solid soffit must be within1" (2.5 cm) maximum above the refrigerator. If the solid soffit ishigher than 1" (2.5 cm) or one is not available, then therefrigerator must be braced.■ It is recommended that board(s) be installed before therefrigerator is installed.■ Board(s) must be long enough to fully cover the width of thecompressor cover.■ Locate the board(s) so the bottom surface(s) of the board(s)is(are) 84" (213 cm) from the floor.■ During installation, raise the refrigerator up so there is¹⁄₄" (6.35 mm) maximum between the top of the refrigeratorand the bottom of the anti-tip board(s). Do not crush thecompressor cover when raising the rear leveling legs.NOTE: The foam gasket, on top of the compressor cover, willcompress to fit under the anti-tip board(s). There is no need totrim the gasket.To Install Anti-tip Boards1. Mark the stud locations on rear wall.2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x81 cm) boards to wall studs behind refrigerator. Use six#8 x 3" (7.6 cm) (or longer) wood screws. The wood screwsmust be screwed into the studs at least 1½" (3.8 cm). Theboard(s) must overlap the compressor cover.Connect the Water SupplyRead all directions before you begin.IMPORTANT: If you turn the refrigerator on before the water line isconnected, turn the ice maker OFF.Connect to Water LineParts Needed■ Minimum 7 ft (2.13 m) flexible, codes approved watersupply lineStyle 1—Shutoff Valve ConnectionNOTE: If your water line connection does not look like Style 1, see“Style 2—Copper Line Connection.”1. Unplug refrigerator or disconnect power supply.IMPORTANT:■ There is not enough clearance to achieve a flush installation ifa water shutoff valve is located in the wall behind therefrigerator. The water shutoff should be located in the basecabinet on either side of the refrigerator.■ Before attaching the tubing to shutoff valve, flush the mainwater supply line to remove particles and air in the water line.Allow enough flow so that water becomes clear. Flushing thewater line may help avoid filters and/or water valves frombecoming clogged.2. Connect the flexible, codes approved water supply line to thewater shutoff valve by threading the provided nut onto theshutoff valve as shown.3. Place the end of the tubing into a bucket, and turn shutoffvalve ON.4. Check for leaks. Tighten any nuts or connections (includingconnections at the valve) that leak.A. Center board¹⁄₄" (6.35 mm) max.above refrigeratorB. Two 2" x 4" x 32" (5 cm x 10 cm x81 cm) boardsC. Attach to studs with six#8 x 3" (7.6 cm) screwsD. Compressor coverBAC2" (5 cm)DA. BulbB. NutC. Water tubingABC