Jenn-Air JXD7036YS Installation Instructions And Use & Care Manual

Also see for JXD7036YS: Design and planning guide

Jenn-Air JXD7036YS Installation Instructions And Use & Care Manual Manual pdf 5 page image

5INSTALLATION REQUIREMENTSTools and PartsGather the required tools and parts before starting installation.Read and follow the instructions provided with any tools listedhere.Tools Needed■ Jigsaw or keyhole saw■ Drill■ ¹⁄₈" (3 mm) drill bit for pilot holes■ Pencil■ Tape measure or ruler■ Flat-blade screwdriver■ Phillips screwdriver■ ³⁄₈" (9.5 mm) nut driver■ Level■ Pliers■ Metal snips■ Wire stripper or utility knife■ Caulking gun and weatherproof caulking compoundParts Supplied■ Top trim - stainless■ End caps (2)■ Lower support legs (2)■ Undercounter mounting brackets (2)■ 4 x 8 mm screws (16)■ 3.5 x 9.5 mm screws (3)■ 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular damper■ 4³⁄₄" (12.0 cm) motor box■ ¼" (6.4 mm) deep cover■ Flat vent cover plate■ 6" (15.2 cm) diameter vent transition with damperParts Needed■ UL listed or CSA approved ½" (12.7 mm) conduit connector■ Wall or roof cap with damper to match vent system■ Vent system■ Home power supply cable■ UL listed wire connectors (3)■ Vent clamps/duct tape as requiredLocation RequirementsNOTE: Downdraft vent is installed directly behind the cooktop.Install the downdraft vent first, then install the cooktop.IMPORTANT: Observe all governing codes and ordinances.■ Have a qualified technician install the downdraft vent. It is theinstaller’s responsibility to comply with installation clearancesspecified on the model/serial/rating plate. The model/serial/rating plate is located on the front of the downdraft ventabove the terminal box cover.■ Downdraft vent location should be away from strong draftareas, such as windows, doors, and strong heating vents orfans.■ Cabinet opening dimensions that are shown must be used.Given dimensions provide minimum clearance.■ Consult the cooktop manufacturer installation instructionsbefore making any cutouts.Check that the downdraft vent and cooktop location willclear the cabinet walls, backsplash, and rear wall studsinside the cabinet.Check for the minimum distance between the front edgeof the countertop and the front edge of the cooktop. Theminimum horizontal distance between the overheadcabinets is the same as the width of the installeddowndraft vent.■ All openings in ceiling and wall where the downdraft vent willbe installed must be sealed.■ Grounded electrical outlet is required. See “ElectricalRequirements” section.■ When installing the downdraft vent, the cabinet drawer willneed to be removed and the drawer front installedpermanently to the cabinet.Cabinet Construction:Downdraft vent is designed for use in a cabinet with a depth of24" (61 cm). Some installations require a countertop deeper than25" (63.5 cm). See the “Countertop Cutout Dimensions Chart.”The maximum depth of the overhead cabinet is 13" (33 cm).Overhead cabinets installed at either side of the downdraft ventmust be 18" (45.7 cm) above the cooking surface.For Mobile Home InstallationsThe installation of this downdraft vent must conform tothe Manufactured Home Construction Safety Standards,Title 24 CFR, Part 328 (formerly the Federal Standard forMobile Home Construction and Safety, title 24, HUD, Part 280)or when such standard is not applicable, the standard forManufactured Home Installation 1982 (Manufactured HomeSites, Communities and Setups) ANSI A225.1/NFPA 501A, orlatest edition, or with local codes.