Jenn-Air JXI8936DS Installation Instructions And Use & Care Manual

Also see for JXI8736DS: Design and planning guide Installation Instructions and Use & Care Guide

Jenn-Air JXI8936DS Installation Instructions And Use & Care Manual Manual pdf 5 page image

5INSTALLATION REQUIREMENTSTools and PartsGather the required tools and parts before starting installation.Read and follow the instructions provided with any tools listedhere.Tools needed■ Level■ Drill with 1¼" (3.0 cm), ½" (12.7 mm) and ³⁄₁₆" (5.0 mm) drillbits■ Pencil■ Tape measure or ruler■ Pliers■ Caulking gun and weatherproof caulking compound■ Vent clamps■ Jigsaw or keyhole saw■ Flat-blade screwdriver■ Metal snips■ Phillips screwdriver■ ½" (13 mm) socket and driver with 24" (61 cm) of extensions■ T20®† TORX® bit or driverParts needed■ Home power supply■ ½" (12.7 mm) UL listed or CSA approved strain reliefsFor vented installations, you will also need:■ 1 wall or roof cap■ Metal vent systemFor non-vented (recirculating) installations, you will alsoneed:■ Chimney Kit Recirculation for non-vented (recirculating)installations only. See “Assistance or Service” section to order.■ Charcoal Filter Part Number W10272069. See “Assistance orService” section to order.Parts suppliedRemove parts from packages. Check that all parts are included.■ Hood canopy assembly with ventilator and lights installed■ Mounting boss/damper/6" (15.2 cm) round flexible metal duct7" (17.8 cm) long (not expanded)■ Filter - installed in hood canopy■ (4) 8 x 80 mm hanger bolts (T20® TORX® drive)■ (4) 8 mm x ½" (13 mm) hex nuts■ (4) 5 x 13 mm mounting screws (T20® TORX® drive)■ Mounting template■ Upper chimney cover■ Lower chimney cover■ ½" (13 mm) special nut tightening tool■ Vent clamp for 6" (15.2 cm) duct■ (2) 3.5 x 9.5 mm screws used for supporting the lowerchimney (located inside canopy behind filters).Location RequirementsIMPORTANT: Observe all governing codes and ordinances.Have a qualified technician install the range hood. It is theinstaller's responsibility to comply with installation clearancesspecified on the model/serial rating plate. The model/serial ratingplate is located behind the left filter on the rear wall of the venthood.Canopy hood location should be away from strong draft areas,such as windows, doors and strong heating vents.Cabinet opening dimensions that are shown must be used. Givendimensions provide minimum clearance.This range hood is recommended for use with cooktops with amaximum total rating of 78,000 BTUs or less.Grounded electrical outlet is required. See “ElectricalRequirements” section.Because of the size and weight of this island hood, the chimneysupport must be securely attached to the ceiling.■ The chimney support must be attached to joists. If this is notpossible, you must build a support structure behind theplaster or drywall. The support structure must be able tosupport 100 lbs (45.4 kg).The range hood is factory set for venting through the roof or wall.For non-vented (recirculating) Installation see “Non-vented(recirculating) Installations” in “Install Range Hood” section.Chimney Kit Recirculation and Charcoal Filter Kit Part NumberW10272069 are available from your dealer or an authorized partsdistributor. See “Assistance or Service” section to order.All openings in ceiling and wall where range hood will be installedmust be sealed.For Mobile Home InstallationsThe installation of this range hood must conform to theManufactured Home Construction Safety Standards, Title 24CFR, Part 328 (formerly the Federal Standard for Mobile HomeConstruction and Safety, Title 24, HUD, Part 280) or when suchstandard is not applicable, the standard for Manufactured HomeInstallation 1982 (Manufactured Home Sites, Communities andSetups) ANSI A225.1/NFPA 501A, or latest edition, or with localcodes.Product Dimensions†®T20 and TORX are registered trademarks of Acument Intellectual Properties, LLC.A. 13" (33.0 cm)B. 11¼" (28.6 cm)C. 28" (71 cm) min.45¼" (115 cm) maxD. 1⁵⁄₈" (4.2 cm)E. 24" (61.0 cm)F. 36" (91.4 cm)BA CDEF