Jensen POWER 1050 Installation And Operation Manual

Jensen POWER 1050 Installation And Operation Manual Manual pdf 4 page image

POWER Amplifiers2Features and SpecificationsYour new Jensen Power mobile stereo power amplifier is the amplifier ofchoice for the high demands of auto sound reproduction. With its deep-bassreproduction and plenty of reserve power, low harmonic distortion and neutralreproduction, the Power series of amplifiers takes Mobile Hi-Fi to new heights.Like all Jensen products, when it comes to accurate sound reproduction thePower series takes a back seat to no one. Jensen will bring your Hi-Fiexperience to new heights with the following features:• MOSFET Power Supply• High Current Bi-Polar Output Transistors• Optimized Class B Design Minimizes Distortion and Reduces Idle Current• Easily Drives 2-Ohm Loads• Pass-Thru RCA's• Variable Bass EQ 0 - 12dB @ 45 Hz• 12dB / Octave Low Pass and High Pass filters• Variable Input Level 400mV - 5V• Short Circuit, DC-offset and Thermal Overload Protection Circuitry• Diagnostic LED's - Green: Power, Red: Standby / FaultPower 400 / 760 / 880 / 920• Low Pass Filter 40 - 300 Hz• High Pass Filter 40 - 300 Hz• High Pass / Low Pass / Full Range Selector Switch• Stereo / Mono Mode Switch (Power 400 and 880 only)• 2/ 3 / 4 Channel Mode Switch (Power 760 and 920 only))Power 900 / 1050• Mono Subwoofer Amp• Low Pass Filter 40 - 240 Hz (Power 900)• Low Pass Filter 40 - 150 Hz (Power 1050)• Subsonic Filter 10 - 40 Hz, 12dB / octave (Power 900)• Subsonic Filter 15 - 55 Hz, 12dB / octave (Power 1050)• Remote Input Level Control (Remote Bass Control) w/ 5 Meter InterfaceCableSpecificationsPower 400 / 760 / 880 / 920• Load Impedance: 2 / 4-Ohm• Signal to Noise @ 1 kHz: >100dB (rated power)• Channel Separation @ 1 kHz: >60dB• Frequency Response: 5-60 kHz, -3dB• Input Impedance: 20 kHz, nominal• THD+N @ 5 Watts: 0.02%, 1 kHz, 14.4VDCPower 900 / 1050• Signal to Noise @ 120 Hz: >100dB (Rated Power)• Channel Separation Not Applicable• THD+N @ 5 Watts: 0.02%, 125 Hz, 14.4VDCPower OutputRMS Power Output @ 2% THD+N, 1kHz, 14.4VDCPower 400• 75 x 2 Watts, 4-Ohm• 100 x 2 Watts, 2-Ohm• 200 x 1 Watts, 4-Ohm BridgedPower 760• 75 x 4 Watts, 4-Ohm• 100 x 4 Watts, 2-Ohm• 190 x 2 Watts, 4-Ohm Bridged StereoPower 880• 135 x 2 Watts, 4-Ohm• 220 x 2 Watts, 2-Ohm• 440 x 1 Watts, 4-Ohm BridgedPower 900• 300 x 1 Watts, 4-Ohm• 450 x 1 Watts, 2-OhmPower 920• 100 x 4 Watts, 4-Ohm• 140 x 4 Watts, 2-Ohm• 230 x 2 Watts, 4-Ohm Bridged StereoPower 1050• 350 x 1 Watts, 4-Ohm• 525 x 1 Watts, 2-OhmSpecifications subject to change without notice.