Kärcher B 60 W Ep Operator's Manual

Also see for B 60 W Ep: Manual

Contents

electrical connection

Kärcher B 60 W Ep Operator's Manual Manual pdf 13 page image

- 3The disc brush must be installed before theinitial operation (see "Maintenance work").The brushes are mounted. Insert the vacuum bar into the vacuumbar suspension in such a manner thatthe profiled sheet is positioned abovethe suspension. Tighten the wing nuts. Insert the suction hose. DANGERRisk of injury! Rotate the programme selec-tor switch to "OFF" to immediately switchoff all functions of the machine. Place long lateral boards of the packag-ing as a ramp next to the pallet. Fix the ramp on the pallet with nails. Place short boards as a support under-neath the ramp. Remove the wooden bars in front of thewheels. Lift the cleaning head by pressing thepedal all the way down. Push down the appliance through theramp from the pallet. DANGERRisk of injury. Push the pedal for raising/lowering the cleaning head with one footonly. The other foot must firmly be placedon the floor.In dangerous situations, release the safetyswitch.Note:Requirements for the extension cable, see"Technical data". Insert the looped end of the extensioncable in the strain relief hook. Plug in the mains plug. Open the lock of the fresh water reser-voir. Fill fresh water (maximum 60 °C) untilthe lower edge of the filling nozzle. Close the lock of the fresh water reser-voir.With automatic fill of fresh water reser-voir (option) Connect the hose to the automatic fill-ing system and open the water supply(max. 60 °C, max. 5 bars). Monitor the appliance - the automaticfilling system will interrupt the watersupply when the tank is full. Shut off the water supply and discon-nect the hose from the appliance. WARNINGRisk of damage. Only use the recommend-ed detergents. With other detergents, theoperator bears the increased risk regardingthe operational safety and danger of acci-dent.Only use detergents that are free from sol-vents, hydrochloric acid and hydrofluoricacid.Follow the safety instructions for using de-tergents.Note:Do not use highly foaming detergents.Recommended detergents: Add the detergent to the fresh waterreservoir. Adjust the water quantity using the reg-ulating button according to the dirt onthe floor covering.Note:Carry out initial cleaning attempts with lowwater volume. Increase water volume step-by-step until the desired cleaning result isachieved.To improve the vacuuming result on tiledfloors the vacuum bar can be turned to anoblique position of up to 5°. Loosen the wing nuts. Turn the vacuum bar. Tighten the wing screws.If the vacuum result is unsatisfactory the in-clination of the straight vacuum bar can bemodified. Adjust the rotary handle to incline thesuction bar. Reducing the speed: Turn the button in"–" direction. Increasing the speed: Turn the button in"+" direction.ATTENTIONRisk of damage to the floor covering. Donot operate the appliance on the spot.Note:The device is designed and built in such away that the cleaning head protrudes to-wards the right. This enables working in acomfortable way close to the edges. Turn the program selection switch tothe desired cleaning program. Press the pedal for lowering the clean-ing head downwards slightly and thenmove it to the left. This unlocks the ped-al. Release the pedal slowly upwards.The cleaning head is lowered.Before StartupInstalling the BrushesBD modelBR modelInstalling the Vacuum BarUnloadingOperationElectrical connectionFilling in detergentsFresh waterDetergentApplication DetergentRoutine cleaning of all waterresistant floorsRM 746RM 780Routine cleaning of glossysurfaces (e.g. granite)RM 755 esRoutine cleaning and basiccleaning of industrial floorsRM 69 ASFRoutine cleaning and basiccleaning of fine stonewaretilesRM 753Routine cleaning of tiles insanitary areasRM 751Cleaning and disinfection insanitary areasRM 732Removal of coating from allalkali-resistant floors (e.g.PVC)RM 752Removal of coating from li-noleum floorsRM 754Setting the water quantitySetting the Vacuum BarOblique positionInclinationSetting the Advance Speed (BDcleaning head only)CleaningLower the cleaning head13EN