Kärcher HDS 5/10 C Original Instructions Manual

Contents

Kärcher HDS 5/10 C Original Instructions Manual Manual pdf 9 page image

– 5Note: Observe handling instructions of the anti-freezeagent manufacturer. Use commercially available anti-freeze agent. Switch on appliance (without heater) till the appli-ance has been completely rinsed.A certain corrosion protection is achieved with this aswell. CAUTIONRisk of personal injury or damage! Consider the weightof the appliance when storing it.Figure 6ATTENTIONRisk of damage! When loading the appliance with aforklift, observe the illustration.ATTENTIONProtect the trigger from damage during transport. CAUTIONRisk of personal injury or damage! Mind the weight ofthe appliance during transport. When transporting in vehicles, secure the appli-ance according to the guidelines from slipping andtipping over. DANGERRisk of injury by inadvertent start-up of appliance andelectric shock. Prior to all work on the appliance, switchoff the appliance and pull the power plug. Shut off water supply. Open the hand spray gun. Switch on the pump with the power switch and al-low to run for about 5-10 seconds. Close the hand spray gun. Set the appliance switch to "0/OFF“. Pull main plug out of socket with dry hands only. Remove water connection. Activate hand spray gun until device is pressureless. Secure the trigger gun. To do so, push the safetycatch towards the front. Allow device to cool down.Your Kärcher vender will inform you about the per-formance of a periodic safety inspection resp. sign-ing of a maintenance contract. Clean the sieve in the water connection. Clean the fine filter. Clean the fuel sieve. Check oil level.ATTENTIONRisk of damage! In case of lacteous oil inform Kärchercustomer service immediately. Clean sieve in the water shortage safe guard. Clean filter at the detergent suck hose. Oil change. Have the maintenance of the device performed bythe customer service. Take out sieve. Clean sieve in water and reinstall. Unpressurize the appliance. Unscrew the fine filter from the pump head. Remove the fine filter and the filter insert. Clean the filter with clean water or compressed air. Reinstall in reverse sequence. Knock the dirt off of the fuel sieve. Do not let thefuel enter the environment. Unpressurize the appliance. Remove the fastening clamp and pull out the hose(soft damping system) of the lack of water fuse. Take out sieve.Note: If necessary turn in screw M8 appr. 5 mm inwardsand therewith pull out sieve. Clean sieve in water. Push sieve inwards. Slide the hose adapter all the way into the lack ofwater fuse and secure it with a fastening clamp. Take out detergent suck supports. Clean filter in water and reinstall. Ready a catch bin for appr 1 Litre oil. Loosen release screw. Tighten release screw. Fill oil slowly up to the MAX marking.Note: Air pockets must be able to leak out.For oil type refer to technical specifications. DANGERRisk of injury by inadvertent start-up of appliance andelectric shock. Prior to all work on the appliance, switchoff the appliance and pull the power plug.– No line voltage, see "Appliance is not running".– Fuel tank empty. Refill fuel.– Detergent tank is empty. Refill detergent.– No power Check power connection/conduit.Flush device with anti-freeze agentStorageTransportCare and maintenanceMaintenance intervalsWeeklyMonthlyEvery 500 operating hours, at least annuallyMaintenance WorksClean the sieve in the water connectionCleaning the fine filterClean the fuel sieveClean sieve in the water shortage safe guardClean filter at the detergent suck hoseOil changeDispose of old oil ecologically or turn in at a gatheringpoint.TroubleshootingIndicator lamp "Ready for use" turns offFuel indicator lamp glowsIndicator lamp for detergent glowsAppliance is not running9EN

/ 12

Related manuals for Kärcher HDS 5/10 C