Kärcher K2 Premium Power Control User Manual

Also see for K2 Premium Power Control: User manual

12 EnglishOperation with a washing brushATTENTIONPaint damageDamage to surfaces through a dirty brushEnsure that the washing brush is free from dirt or otherparticles before using it.NoteThe device operates at low pressure when using wash-ing brushes. This means that detergent can be mixedwith the water.1. Insert the washing brush into the high-pressure gunand turn by 90° to fasten it.Operation with detergent DANGERFailure to adhere to the safety data sheetIncorrect handling of the detergent can seriously dam-age your healthObserve the safety data sheet of the detergent manu-facturer, in particular the instructions on personal pro-tective equipment.NoteDetergent can only be mixed into the jet at low pressure.NoteKÄRCHER detergents ensure fault-free operation. Askus for a consultation, request our catalogue or our de-tergent information sheets.1. Fill the detergent solution into the detergent tank.Adhere to the dosage specifications on the deter-gent container.Illustration J2. Close the detergent tank with the cover.Illustration D3. Latch the detergent tank in the device.4. Use the Click-Vario Power spray lance.5. Turn the spray lance to "MIX".The detergent solution is mixed with the water jetduring operation.6. You can optionally use the foam nozzle.a Connect the foam nozzle to the detergent bottle.Illustration Kb Insert the foam nozzle into the high-pressure gunand turn by 90° to fasten it.Recommended cleaning method1. Spray the detergent sparingly on the dry surface andlet it work for a while (do not let it dry).2. Rinse off the loosened dirt with the high-pressurejet.After operation with detergent1. Flush the device with clear water for approx. 30 sec-onds.Interrupting operation1. Release the lever of the high-pressure gun.The device switches off when the lever is released.The high pressure in the system is retained.2. Lock the lever of the high-pressure gun.Illustration L3. Place the high-pressure gun with the spray lance inthe parking position.4. Switch the device off "0/OFF" during work breakslonger than 5 minutes.Ending operation CAUTIONPressure in the systemInjuries from high-pressure water escaping uncontrolla-blyOnly disconnect the high-pressure hose from the high-pressure gun or the device when the system is fully de-pressurised.1. Release the lever of the high-pressure gun.2. Close the water tap.3. Press the lever of the high-pressure gun for 30 sec-onds.The pressure remaining in the system is discharged.4. Release the lever of the high-pressure gun.5. Lock the lever of the high-pressure gun.6. Disconnect the device from the water supply.7. Switch off the device "0/OFF".8. Pull the mains plug out of the socket.Transport CAUTIONFailure to observe the weightRisk of injury and damageBe aware of the weight of the device during transporta-tion.Carrying the device1. Lift up the device by the carrying handle, and carryit.Pulling the device1. Pull the transport handle out until it audibly latchesinto place.2. Pull the device via the transport handle.Transporting the device in a vehicle1. Drain the detergent tank.2. Secure the device against slipping and tipping over.Storage CAUTIONFailure to observe the weightRisk of injury and damageBe aware of the weight of the device during storage.Storing the device1. Place the device on a level surface.2. Disconnect the spray lance from the high-pressuregun.3. Disconnect the high-pressure gun from the high-pressure hose.4. Disconnect the high-pressure hose from the device.5. Store the high-pressure hose on the device.6. Store the mains connection cable and accessorieson the device.Observe the additional notes before storing the devicefor a long period of time, see chapter Care and service.Frost protectionATTENTIONDanger of frostIncompletely emptied devices can be destroyed byfrost.Completely empty the device and accessories.Protect the device from frost.The following requirements must be satisfied: The device is disconnected from the water supply. The high-pressure hose is removed.1. Switch the device on "I/ON".2. Wait for a maximum of 1 minute until no more waterescapes from the high-pressure connection.3. Switch off the device.4. Store the device in a frost-protected room, togetherwith all accessories.

/ 9

Related manuals for Kärcher K2 Premium Power Control