Kaysun KPDHF-71 DN3.0 Installation Manual

Also see for KPDHF-112 DN3.0: Owner's manual

Contents

Kaysun KPDHF-71 DN3.0 Installation Manual Manual pdf 3 page image

installation manual1CONTENTS PAGE Disassembling, replacement and maintenance offilter should be carried out by qualified person.If the supply cord is damaged, it must be replaced by themanufacturer or its service agent or a similarly qualified personto avoid a hazard.An all-pole disconnection switch having a contact separation ofat least 3mm in all poles should be connected in fixed wiring.The appliance shall be installed in accordance with nationalwiring regulations.The temperature of refrigerant circuit will be high, please keepthe interconnection cable away from the copper tube.An all-pole disconnection device which has at least 3mmseparation distance in all pole and a residual current device(RCD) with the rating of above 10mA shall be incorporated in thefixed wiring according to the national rule.The power cord type designation is H05RN-R/H07RN-F or above.2. INSTALLATION PLACE1. INSTALLATION PRECAUTIONTo install properly, please read this manual at first.The air conditioner must be installed by qualified persons.When installing the indoor unit or its tubing, please follow thismanual as strictly as possible.When all the installation work is finished, please turn on the poweronly after a thorough check.No further announcement if there is any change of this manualcaused by product improvement.The installer should illustrate to users how to correctly use andmaintain the air-conditioner, as well as remind users to carefullyread and keep both Installation Manual and Owner's Manualwell.DISPOSAL: Do not dispose this product as unsorted municipalwaste. Collection of such waste separately for special treatmentis necessary.This appliance is not intended for use by persons (includingchildren) with reduced physical, sensory or mental capabilities,or lack of experience and knowledge, unless they have beengiven supervision or instruction concerning use of the applianceby a person responsible for their safety.Children should be supervised to ensure that they do not playwith the appliance.Disconnect the power supply before cleaning and maintenance.The appliance must be installed 2,3m above floor.The appliance shall not be installed in the laundry.The appliance shall be installed keep away from quiet place,such as bedroom.Indoor Unit● Enough room for installation and maintenance.● The ceiling is horizontal and it can afford the weight of the indoorunit.● The air inlet and outlet are not impeded and does not affected byoutdoor air too much.● The air flow can reach every part of the room.● The connecting pipe and drainpipe can be easily extracted out.● There is no direct radiation from heat source.Outdoor Unit● Enough room for installation and maintenance.● The air inlet and outlet are not impeded and does not affected byoutdoor air too much.● Dry and well-ventilated place.● The supporter is flat and horizontal and can afford the weight ofoutdoor unit, without noise and vibration.● The noise and the outlet air will not influence your neighbor.● No combustible gas.● Place convenient for piping and wiring.Please keep away from the following places, or malfunction maybe caused.(if unavoidable, please consult the professionals):There is mineral oil like the oil of cutting machine.● There is much salty air. (Near the coast)● There is caustic gas such as sulfuric gas. (Near the hot spring.)● Factory where the voltage fluctuate greatly.● In the car or in the cabin.● In the kitchen or a place full of oil steam.● There is strong electromagnetic wave.NOTEINSTALLATION PRECAUTION ............................................................... 1INSTALLATION PLACE. ........................................................................ 1INDOOR UNIT INSTALLATION ................................................................2INSTALLATION SPACE ........................................................................ 10REFRIGERANT PIPE.............................................................................. 10DUCT DESIGN ...................................................................................... 11INSTALL THE CONNECTING PIPE ..................................................... 17REFRIGERANT PIPE CONNECTION................................................... 18CONNECT THE DRAIN PIPE............................................................... 19CONTROL ............................................................................................. 21TROUBLE SHOOTING. ......................................................................... 24INSTALL ELECTRICTHROTTLE PART ................................................. 25INSTALL BRANCH PIPE. ..................................................................... 25TEST OPERATION. .............................................................................. 25