Kenwood DNX4280BT Service Manual

Also see for DNX5380: Instruction manual Quick start quide Instruction manual

Contents

16DNX4280BT/5180/5280BT/5380/5380M/5380BT/5580BT/6040EX/6180/6480BT/6980TEST MODE1 General information1.1 PurposeThe purpose of this document is to define the items re-quired for the test mode used at the manufacturing processand service stations for 11 Visual Mid / Entry model.1.2 Scope of applicationThis document is applied for the models described in Table1.2.1. (This document also describes the presence or ab-sence of the functions related to the Test mode.)1.3 OutlineThis section describes the Test mode of the 11 Visual Mid/Entry model regarding the display specifications, the speci-fications of the operation with the key remote controller, andthe details of its behavior.2 Test Mode specification2.1 OperationsThe system can be transferred to the Test mode with thefollowing two approaches:Regardless of the ON/OFF status of security, the systemcan be transferred to the Test mode with one of the follow-ing operations.q Start the system by pressing [Reset] key while pressingthe following keys.Mid : [MENU] + [ATT]Entry : [Eject] + [SCRN]w Input [2] → [] → [3] with the remote controller (SW:AUD) into the standby source.ModeltypeDesti-nation Model NamePanelmecha-nismAttachable/detachablepanelBTBuilt-in Ext SWElectro-statictouchDivX KAB I/F DSP SteeringRemoteTMCTuner SD SlotDNX(Mid)K DNX7180 c ° c c c ° c c ° c cR DNX7480BT c ° c c c c ° c ° ° cE DNX7280BT c c c c c c c c ° c cM DNX7380BT c c c c c c ° c c c cM2 DNX7380BTM c c c c c c ° c c ° cX DNX7380BT c c c c c c ° c c ° cDNX(Entry)K DNX6980 ° ° c ° ° ° c ° ° c cK DNX6180 ° ° c ° ° ° c ° ° c °K2 DNX6040EX ° ° c ° ° ° c ° ° c °R DNX6480BT ° ° c ° ° c ° ° ° ° cE DNX5280BT ° c c ° ° c c ° ° c cQ DNX5580BT ° c c ° ° c ° ° ° c cX DNX5380BT ° c c ° ° c ° ° c ° cER DNX4280BT ° ° c ° ° c ° ° ° c °K DNX5180 ° ° ° ° ° ° c ° ° ° °M DNX5380 ° c ° ° ° c c ° c c cM2 DNX5380M ° c ° ° ° c c ° c ° cV DNX5380 ° c ° ° ° c c ° c ° cTable 1.2.1 Model List of 11 Visual Mid/Entry modelWhile in the test mode, flash ILLUMI of the EJECT port in 1sec intervals regardless of the panel position (only Mid).In the Test mode, the LED for SI flickers at regular intervals.Panel: Flash (all models)Sub panel: Turn off when panel is attached. Flash whenpanel is detached. (Only for attachable/de-tachable model)When starting in the Test mode, the illumi is turned ON inwhite.Turn the system OFF in 30 minutes when it is started in theTest mode.Continue the test mode by ACC OFF/ON. Clear the testmode by Reset.2.2 Specification of screensThis section describes the Test mode functions availablein each screen. (The screen layout may differ from the realsystem.)