Kenwood KAC-8102D Instruction Manual

Also see for KAC-8102D: Instruction manual Service manual Service manual Instruction manual

Contents

English 5ControlsNOTEThe control panel locates under the front side cover. Remove the cover toaccess to its controls for adjustment. (See page 3)1 Fuse (KAC-9152D/9102D: 30 A × 2)Fuse (KAC-8152D/8102D: 40 A × 1)NOTEIf you can’t find the specified capacity fuse at your store etc., consult yourKenwood dealer.2 Battery terminal3 Ground terminal4 Power control terminalControls the unit ON/OFF.NOTEControls the unit power. Be sure to connect it with all the systems.5 Speaker output terminals• KAC-9152DAs this unit accepts speakers with a minimum impedance of 1 ohm,connect speakers with 1-ohm or higher impedance to these terminals.• KAC-9102D/8152D/8102DAs this unit accepts speakers with a minimum impedance of 2 ohms,connect speakers with 2-ohms or higher impedance to these terminals.2CAUTIONThe rated input of the speakers should be no less than the maximum outputof the amplifier. Otherwise malfunction may result.6 REMOTE terminal (KAC-9152D/8152D only)Connects the Remote cable.NOTEUse the Remote cable of the accessory.7 Speaker level input terminalsNOTE• The genuine-accessory car stereo shall have a maximum power output ofno more than 40 W.• Do not connect the speaker output leads from a power amplifier (Optional)to the speaker level input terminals of this unit, for this may causemalfunction or damage.• Do not connect cables and leads to both RCA cable input jacks andthe speaker level input terminals simultaneously, for this may causemalfunction or damage.• Connect the power control lead to a power supply which can be turnedON/OFF by the ignition key switch (ACC line). With this connection, shocknoise may be generated when the power of the genuine-accessory carstereo is switched ON/OFF.8 RCA cable ground lead terminalWhen using an RCA cable with a ground lead attached, connect the groundlead to this terminal.9 LINE IN terminal0 LINE OUT terminalThe signal that’s input from the line input terminal is output.! Power indicatorWhen the power is turned on, the Power indicator lights.If the Power indicator does not light when the power is turned on, theprotection function may be activated. Check whether there is any indicationof trouble. (See page 2)@ BASS BOOST LEVEL control (KAC-9102D/8102D only)Sets the low frequency level to be compensated.# LPF(Low-Pass Filter) FREQUENCY controlThis control adjusts the frequency band output from this unit.$ ISF (infrasonic filter) switchUltralow frequencies that cannot be reproduced even by a subwooferspeaker do not become sound but become unnecessary oscillations, whichaffect the sound by causing distortion, etc. Setting this switch to "15 Hz" or"25 Hz" cuts the frequencies below the respective frequency.This improves the reproduction performance of the speakers by eliminatingunnecessary oscillations which will not become sound.% PHASE switchWhen this switch is set "180°" (Reverse) the speaker output phase is reversed.^ INPUT SENSITIVITY controlSet this control according to the pre-output level of the center unitconnected with this unit, or to the maximum power output of the genuine-accessory car stereo.Use the diagram on the right as a guide.NOTEFor the pre-output level or the maximum power output, refer to the in the instruction manual of the center unit.& BOOST LEVEL (Bass boost level) control (KAC-9152D/8152Donly)Sets the level by which the low frequency range should be boosted.* FREQUENCY (Bass boost frequency) control (KAC-9152D/8152D only)Sets the center frequency around which the low frequency range should beboosted."//34,%6%,D" &2%15%.#9(Zp q r s t u v w x y z { } ~| } ~| 8o8KAC-9102D/8102DKAC-9152D/8152DRemote controller(KAC-9152D/KAC-8152D only)