Kenwood KDC-1032 Service Manual

Also see for KDC-1032: Instruction manual

Contents

Kenwood KDC-1032 Service Manual Manual pdf 9 page image

9KDC-1032/132/132CRKDC-133/233/234SGYTEST MODE● How to enter the test mode• Press Preset [1] and Preset [3] keys simultaneously to re-set the unit.● How to clear the test modeReset. (Do not clear by Power OFF and ACC OFF.)● Initial conditions of the test mode• Source is STANDBY.• Displays lights are all turned on.• The volume is at -10dB (The display is 30).• CRSC is OFF, regardless of whether there are switchingfunctions or not.• LOUD is OFF.• SYSTEM Q is NATURAL (FLAT).• BEEP should always work by pressing a key.● Test mode specification for TUNER• TUNER (FM) Preset [4] key shall be 98.3MHz.● CD receiver test mode specifications• Forced discharging operation is prohibited at reset start. Notethat a CD is not to be recognized by reset when it is in-serted.• [Track up] key triggers a jump to the following tracks.No. 9 → No. 15 → No. 10 → No. 11 → No. 12 → No. 13 →No. 22 → No. 14 → No. 9 (recursive)• [Track down] key moves back to the previous track from thecurrent track.• Preset [1] key triggers a jump to No. 28.• Preset [2] key triggers a jump to No. 14. (Scan function isinvalid.)● Audio adjust mode• Pushing the [VOL] key enters the audio function mode.• The initial item is Fader. (FAD → BALANCE → BASS →MID → TRE)• Use [AM/FM] key to switching items.• Use [Seek Up/Down] key to switching the adjusted value.• Adjust Fader/Balance to three levels (15 ↔ 0 ↔ 15) withVolume up/down. (initial value: 0)• Adjust Bass/Middle/Treble to three levels (-8 ↔ 0 ↔ +8)with Volume up/down. (initial value: 0)• Pressing the [VOL] key for more than a second enters theaudio setup mode.• Use [AM/FM] key to switching items.• Use [Seek Up/Down] key to switching the adjusted value.• Adjust Volume offset to two levels (-8 ↔ 0). (initial value: 0)• Initialize everything with the [Track-Up] key in the standbysource.• Pressing [∗] key on the remote controller enters the audioadjustment mode. (Use [∗] key to cancel. KDC-132CR only)• Continuous feed with a remote controller shall not be used.Pressing a key activates a motion. (KDC-132CR only)● Special display when all lights are onThe following information will be displayed by pressing thepreset key when STANDBY indicators are on.[1] key • Press [1] key. The current destination SW is displayed.(Display) TP-X• Press a key while the destination SW is displayed.Version display (month, date, hour, minute in 8 digits)(Display) XXXX xxxx[2] key • All LCD light up.[3] key • Press the key for less than a second: Power-on timedisplay (STANDBY time should not be counted).• Press the key for more than 2 seconds while thepower-on time is displayed: The power-on time iscleared.(Display) Pon_x XXXX MAX 60000 (time)[4] key • Press the key for less than a second: CD operationtime display.• Press the key for more than 2 seconds while the CDoperation time is displayed: CD operation time iscleared.(Display) PLY_x XXXX MAX 60000 (time)[5] key • Press the key for less than a second: CD EJECTcount display.• Press the key for more than 2 seconds while the CDEJECT count is displayed: CD EJECT count iscleared.(Display) EJC_x XXXX MAX 60000 (time)