Kenwood KDC-216S Service Manual

Also see for KDC-2018: Instruction manual

Contents

KDC-216S/20184MICROCOMPUTER'S TERMINAL DESCRIPTIONlTerminal DescriptionPin Function I/O Description Processing Operation1 AV CONT O A/D converter reference voltage control output ”Hi”: ON / ”Lo”: OFF2 IC2 TYPE0 I IC2 setting terminal ”Lo”: Initial value3 IC2 TYPE1 I IC2 setting terminal ”Lo”: Initial value4 AVSS - Ground connection terminal connected to GND5 M MUTEL I Muting request from the MICOM. of CD mecha. ”Lo”: Mute request6 N.C O Not used7 AVREF1 I D/A converter reference voltage input8 ILLUMI O Illumination AVR ON/OFF control output ”Hi”: AVR ON9 L RES O Reset output to the LCD driver IC ”Lo”: Reset10 PANEL I Panel open/close detection input ”Lo”: Panel closed11 L DATAL I Data input from the LCD driver IC12 L DATAS O Data output to the LCD driver IC13 L CLK O Clock output to the LCD driver IC14 N.C O Not used15 N.C O Not used16 CH-DATAC I Data input from changers17 CH-DATAH O Data output to changers18 CH-CLK I/O Clock input/output with changers19 L CE O CE output to the LCD driver IC ”Hi”: Active20 N.C O Not used21 M RST O Reset output to the MICOM. of CD mecha. ”Lo”: Reset22 M STOP O Stop request to the MICOM. of CD mecha. ”Lo”: Stop23 MOSW O CD mechanism loading motor control output ”Hi”: Loading & Eject / ”Lo”: other24 PLL SCL O Clock output to the tuner pack25 AM+B O AM+B control ”Hi”: during AM reception26 FM+B O FM+B control ”Hi”: during FM reception27 M-SCL I/O Clock input/output with the MICOM. of CD mecha.28 DSI O DSI output ”Hi”: LED ON29 LO/EJ I/O CD mecha.Loading/Eject switching output ”Lo”: Loading / ”Hi”: Eject30 SW3 I Down & limit switch detection input ”Hi”: Chucking / ”Lo”: Pickup most inner position31 R DATA I Data input from RDS decoder32 R QUAL I Quality input from RDS decoder33 VSS1 - Ground connection terminal connected to GND34 SD I SD input from the tuner pack ”Hi”: Station detected35 IC2 SCL O Clock output to the E-VOL. IC36 M-SDA I/O Data input/output with the MICOM. of CD mecha.37 PLL SDA I/O Data input/output with the tuner pack38 IC2 SDA I/O Data input/output with the E-VOL. IC39 MUTE O Mute control output ”Hi”: Mute ON / ”Lo”: Mute OFF40 N.C O Not used41 AFC O AFC control output ”Lo”: during FM seek42 CH-REQH O Request output to changers ”Lo”: Request43 CH-CON O Changer control ”Lo”: Standby / ”Hi”: ON44 N.C O Not used45 P MUTE O Power IC mute control ”Lo”: Mute46 SVR O Power lC reset terminal When the momentary power down, after ACCOFF/ON is detected and after POWER ON/OFF, the output goes ”Hi” temporarily.47 STBY O Power IC standby control output ”Hi”: POWER ON mode48 P CON O Power control ”Hi”: POWER ON mode except ALL OFF mode49 P ANT O Antenna control ”Hi”: during FM/AM reception50 BEEP O BEEP sound output51 ACC DET I ACC detection input ”Hi”: ACC OFF / ”Lo”: ACC ON52 BU DET I Momentary power down detection input ”Hi”: When momentary power down detectedor BU OFF / ”Lo”: BU ON53 N.C O Not used