Kenwood KDC-W8534 Service Manual

Also see for KDC-W8534: Instruction manual

Contents

Kenwood KDC-W8534 Service Manual Manual pdf 15 page image

15KDC-W8534/W8534YKDC-X790TEST MODE● How to enter the test modeIn order to enter the test mode, reset the unit while simulta-neously pressing down [1] and [3] keys.(While “----” is being displayed, power can be ON for 30 min-utes.)● How to clear the test modeThe test mode is cleared in case of any of the following events:resetting, momentary power down, Acc OFF, Power OFF andremoval of the panel.● Initial conditions of the test mode• Source is STANDBY.• Displays lights are all turned on.• The volume is at –10dB (The display is 30).• Loudness (LOUD) is OFF.• CRSC is OFF, regardless of whether there are switchingfunctions or not.• SYSTEM Q is NATURAL (=FLAT).• BEEP will sound anytime with a less than 1 second push.• Auxiliary (AUX) is ON.• DISPLAY TYPE is TYPE D.• The Multi-function Key System are source dependent sys-tems. (TUNER → Preset, CD / CD-CH → Scan, etc.)• Display of TUNER sources will be as follows :European Models : Upper Display=PS/frequency, MiddleDisplay=spectrum analyzer, Lower Display=multi-functionOther Models : Upper Display=SNPS, Middle Display =spec-trum analyzer, Lower Display=multi-function• CD source display will be as follows :All Models : Upper Display=P-TIME, Middle Display= spec-trum analyzer, Lower Display=multi-function● RDS automatic measurementConventionally, the PS display has been visually checked onthe production line. This will be replaced by a new processing.The PS data will be received and the PS contents is to beverified as “RDS_TEST”. When this is verified, the P-CONterminal is forced to go OFF. (In this case, “ _ ” means blank.)→ This will be a dedicated test mode processing.On the P-CON, when power is turned off once and, then,turned on again, (Power OFF → ON) the unit will be re-started.● Special display when set to TUNERWhen in TUNER mode, if any of the following displays appear,there is an abnormality with the front end.• “TNE2P_NG” : Front-end E2PROM values are still default(not determined).• “TNCON_NG” : In this condition, the communication withthe front-end is not possible.● Forced switching of K3IIn TUNER FM mode, each time [6] key is pressed, the func-tions move in the following cycle :AUTO → forced WIDE → forced MIDDLE → force NARROW→ AUTOThe initial condition is AUTO and the displays below will ap-pear.• AUTO : FMA• Forced MIDDLE : FMM• Forced WIDE : FMW• Forced NARROW : FMN● CD receiver test mode specifications• Jumps are made to the following tracks by pressing the[ ] key.∗ KDC-W8534/W8534YNo. 9 → No. 15 → No. 10 → No. 11 → No. 12 → No. 13 →No. 22 → No. 14 → No. 9 → No. 11 → No. 9 (Returns tothe beginning)∗ KDC-X790/MP732/MP8533No.9 → No.15 → No.10 → No.11 → No.12 → No.13 →No.22 → No.14 → No.9 (Returns to the beginning)It must be noted, however, that when paying MP3 / WMA /AAC disk, which contain 8 files or less, the first track andthe following tracks are played in order.• When [ ] key is pressed, it goes down by 1 track.• When a CD is used as a source, by pressing [1] key for lessthan 1 second, a jump to the Track No. 28 is made.• When a CD is used as a source, by pressing [2] key for lessthan 1 second, a jump to the Track No. 14 is made.• When a CD is used as a source, by pressing [3] key for lessthan 1 second, a display of CD mechanism model nameand its version is made. When the pressing of [3] key forless than 1 second is made for the second time, the normaldisplay is resumed. (Time code display)• While in CD source, use [5] key to switch between DSPThrough and DSP Bypass. (In models with DSP)The multi-function key 5 indicates Through, and 5 in-dicates Bypass.• When a CD is used as a source, by pressing [6] key for lessthan 1 second, a jump to the Track No. 15 is made. At thesame time, the volume value is set to 27 (5V PRE).