ENGLISH 31Data Size: B6L (182 mm x 128 mm)Book Size: B6L (182 mm x 128 mm)SPECIFICATIONSAudioMaximum Output Power 50 W × 4Full Bandwidth Power 22 W × 4 (at less than 1 % THD)Speaker Impedance 4 Ω — 8 ΩTone Action Band 1: 62.5 Hz ±9 dBBand 2: 100 Hz ±9 dBBand 3: 160 Hz ±9 dBBand 4: 250 Hz ±9 dBBand 5: 400 Hz ±9 dBBand 6: 630 Hz ±9 dBBand 7: 1 kHz ±9 dBBand 8: 1.6 kHz ±9 dBBand 9: 2.5 kHz ±9 dBBand 10: 4 kHz ±9 dBBand 11: 6.3 kHz ±9 dBBand 12: 10 kHz ±9 dBBand 13: 16 kHz ±9 dBPreout Level/Load (USB) : 4 000 mV/10 kΩ/ / :2 500 mV/10 kΩPreout Impedance ≤ 600 ΩGeneralOperating Voltage 14.4 V (10.5 V — 16 V allowable)Maximum Current Consumption 10 AOperational Temperature Range –10°C — +60°CInstallation Size (W × H × D) :182 mm × 53 mm × 159 mm (7-3/16” × 2-1/16” × 6-1/4”)/ / :182 mm × 53 mm × 107 mm (7-3/16" × 2-1/16" × 4-3/16")Weight : 0.85 kg (1.87 lbs)/ / :0.7 kg (1.54 lbs)Subject to change without notice.INSTALLATION / CONNECTIONWarning• The unit can only be used with a 12 V DC power supply, negative ground.• Disconnect the battery’s negative terminal before wiring and mounting.• Do not connect Battery wire (yellow) and Ignition wire (red) to the carchassis or Ground wire (black) to prevent a short circuit.• Insulate unconnected wires with vinyl tape to prevent a short circuit.• Be sure to ground this unit to the car’s chassis again after installation.Caution• For safety’s sake, leave wiring and mounting to professionals. Consult thecar audio dealer.• Install this unit in the console of your vehicle. Do not touch the metal partsof this unit during and shortly after use of the unit. Metal parts such as theheat sink and enclosure become hot.• Do not connect the [ wires of speakers to the car chassis or Ground wire(black), or connect them in parallel.• Mount the unit at an angle of less than 30º.• If your vehicle wiring harness does not have the ignition terminal, connectIgnition wire (red) to the terminal on the vehicle’s fuse box which provides12 V DC power supply and is turned on and off by the ignition key.• Keep all cables away from heat dissipate metal parts.• After the unit is installed, check whether the brake lamps, blinkers, wipers,etc. on the car are working properly.• If the fuse blows, first make sure the wires are not touching car’s chassis,then replace the old fuse with one that has the same rating.Basic procedure1 Remove the key from the ignition switch, thendisconnect the [ terminal of the car battery.2 Connect the wires properly.See Wiring connection. ( 33, 34)3 Install the unit to your car.See Installing the unit (in-dash mounting).4 Connect the [ terminal of the car battery.5 Press to turn on the power.6 Detach the faceplate and reset the unit within5 seconds. ( 3)JS_KWD_KMM_BT515HD_KN_EN_3.indd 31JS_KWD_KMM_BT515HD_KN_EN_3.indd 31 13/10/2015 9:57:30 AM13/10/2015 9:57:30 AM