Kenwood NX-300S Service Manual

Also see for NEXEDGE NX-300: Brochure Instruction manual Instruction manual Instruction manual Instruction manual

NX-300(S)32TROUBLE SHOOTINGFault Diagnosis of the BGA (Ball Grid Array) IC■ OverviewA fl owchart for determining whether or not the transceiver can be powered on due to broken BGA parts.■ BGA partsASIC (IC108), DSP (IC102), FLASH (IC101), SRAM (IC103)When the BGA IC is problematic, please bring the printed circuit board (X53-4432-77) in for service. Various ESN/default ad-justment values are written on the printed circuit board for service.Additionally various ESN stickers are included. (Please refer to pages 34 and 35.)Button type lithium battery (W09-0971-05) does not belong to the printed circuit board for service. Please use the part whichhas been attached to the printed circuit board. After the printed circuit board has been readjusted, please attach any ESNstickers to the chassis. When “ESN Validation” is used with NXDN Trunking, you must modify the ESN register.● Checking power supply voltageChecking voltagePoints to be checked Normal voltage33M IC404 (3 pin) 3.3V15M IC717 (4 pin) 1.5V33A IC406 (5 pin) 3.3V31BU IC416 (3 pin) 3.1VPower supply of each device is connected through the coil.[ASIC]33M: L714, 15M: L715, 33A: L716[DSP]33M: L712, 15M: L711[FLASH]33M: L717[SRAM]31BU: L710● Checking the clockChecking the clockPoints to be checked Normal voltage (3.3V)18.432MHz ASIC side R158 18.432MHzASIC & DSP side R159 18.432MHz32.768kHz IC106 (1 pin) 32.768kHzWhen a normalvalue is confirmed.When a normalvalue is confirmed.● Checking the Reset/Control signalChecking the control signal input to the ASICPoints to be checked Normal voltageRESET IC105 (4 pin) 3.3V/BINT Q401 (6 pin) 3.3V/PSW Q402 (3 pin) 3.3VChecking the control signal output from the ASICPoints to be checked Normal voltage/FRST C110 3.3VIf the /FRST is always 0V, the ASIC is broken.If the /FRST repeats 3.3V and 0V at intervals,The ASIC, FLASH and SRAM may be broken.The BGA parts are not broken.Checking for an abnormal point33M has an abnormal voltage.[ASIC]Remove L714 to check the voltage of the 33M.If the voltage becomes normal, the ASIC is broken.[DSP]Remove L712 to check the voltage of the 33M.If the voltage becomes normal, the DSP is broken.[FLASH]Remove L717 to check the voltage of the 33M.If the voltage becomes normal, the FLASH is broken.15M has an abnormal voltage.[ASIC]Remove L715 to check the voltage of the 15M.If the voltage becomes normal, the ASIC is broken.[DSP]Remove L711 to check the voltage of the 15M.If the voltage becomes normal, the DSP is broken.33A has an abnormal voltage.[ASIC]Remove L716 to check the voltage of the 33A.If the voltage becomes normal, the ASIC is broken.31BU has an abnormal voltage.[SRAM]Remove L710 to check the voltage of the 31BU.If the voltage becomes normal, the SRAM is broken.If the voltage is not corrected, there is a problemother than the BGA parts.When an abnormalvalue is confirmed.When an abnormalvalue is confirmed.When an abnormalvalue is confirmed.When an abnormalvalue is confirmed.When a normalvalue is confirmed.When a normalvalue is confirmed.