Kenwood TH-K2AT Service Manual

Also see for TH-K2AT: Service manual Instruction manual Instruction manual

TH-K2AT/K2E/K2ET32J. 13.8V TX M pow er (Low er limit frequency, centerfrequency, upper limit frequency)113.8V TX M pow er (Low er limit frequency)(1) Press the [LAM P] or [M ONI] key on the transceiver to display“ P13L” on the LCD.In this case, the “ ” icon appears.The current APC value is displayed at the low er digits ofthe frequency display, and the value stored in the EEPROMis displayed on the memory channel number display.(2) Press the [VFO], [M R] or [CALL] key to sw itch to thefrequency display.(3) Turn the encoder to display the low er limit frequency onthe LCD.(4) Press the [CALL] key to sw itch to the adjustment display.(5) Press the [PTT] key to enable the transmit mode.(6) Turn the encoder to change the current APC value and adjustthe transmission pow er.(7) Press the [M ENU] key to w rite the current APC value intothe EEPROM .213.8V TX M pow er (Center frequency)(1) Press the [LAM P] or [M ONI] key on the transceiver to display“ P13C” on the LCD.In this case, the “ ” icon appears.(2) Press the [VFO], [M R] or [CALL] key to sw itch to thefrequency display.(3) Turn the encoder to display the center frequency on theLCD.(4) Repeat steps (4) to (7) of “ 113.8V TX M pow er (Low erlimit frequency)” described on page 31.313.8V TX M pow er (Upper limit frequency)(1) Press the [LAM P] or [M ONI] key on the transceiver to display“ P13H” on the LCD.In this case, the “ ” icon appears.(2) Press the [VFO], [M R] or [CALL] key to sw itch to thefrequency display.(3) Turn the encoder to display the upper limit frequency onthe LCD.(4) Repeat steps (4) to (7) of “ 113.8V TX M pow er (Low erlimit frequency)” described on page 32.K. 13.8V TX L pow er (Low er limit frequency, centerfrequency, upper limit frequency)113.8V TX L pow er (Low er limit frequency)(1) Press the [LAM P] or [M ONI] key on the transceiver to display“ P13L” on the LCD.In this case, the “ ” icon appears.The current APC value is displayed at the low er digits ofthe frequency display, and the value stored in the EEPROMis displayed on the memory channel number display.(2) Press the [VFO], [M R] or [CALL] key to sw itch to thefrequency display.(3) Turn the encoder to display the low er limit frequency onthe LCD.(4) Press the [CALL] key to sw itch to the adjustment display.(5) Press the [PTT] key to enable transmit mode.(6) Turn the encoder to change the current APC value and adjusttransmission pow er.(7) Press the [M ENU] key to w rite the current APC value intothe EEPROM .213.8V TX L pow er (Center frequency)(1) Press the [LAM P] or [M ONI] key on the transceiver to display“ P13C” on the LCD.In this case, the “ ” icon appears.(2) Press the [VFO], [M R] or [CALL] key to sw itch to thefrequency display.(3) Turn the encoder to display the center frequency on theLCD.(4) Repeat steps (4) to (7) of ” 113.8V TX L pow er (Low er limitfrequency)” described on page 32.313.8V TX L pow er (Upper limit frequency)(1) Press the [LAM P] or [M ONI] key on the transceiver to display“ P13H” on the LCD.In this case, the “ ” icon appears.ADJUSTM ENT