LAZBOY PowerReclineXR+ Series Operating Instructions Manual

Also see for PowerReclineXR+ Series: Operating instructions

Contents

LAZBOY PowerReclineXR+ Series Operating Instructions Manual Manual pdf 9 page image

1716PowerReclineXR®+ & PowerReclineXRw+TMTroubleshooting– To reduce the risk of serious injury:• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand hasbeen dropped in water or any liquid. Contact your La-Z-Boy ® dealer for service.WARNINGPress and hold thebutton down to returnthe back to the uprightposition. Release thebutton to stop the backin any reclined positionor when fully raised.Press and hold thebutton down to closethe legrest and returnthe chair body. Releasethe button to stop thelegrest in any extendedposition or whenfully closed.Press and hold thebutton down to raisethe back and close thelegrest and return thechair body. Releasethe button to stop thechair in any position orwhen the back is fullyraised and the legrestis fully closed.Press and hold thebutton down to returnthe headrest. Releasethe button to stop theheadrest in any positionor when fully retracted.Press and hold the button downto decrease the lumbar intensity.Release the button to stop the lumbarin any position or when fully retracted.Press and hold thebutton down to reclinethe chair back. Releasethe button to stop theback in any reclinedposition or whenfully reclined.Press and hold thebutton down to extendthe legrest and tilt thechair body backward.Release the button tostop the legrest in anyextended position orwhen fully raised.Press and hold thebutton down to reclinethe back, extendthe legrest and tilt thechair body backward.Release the button tostop the chair in anyposition or when theback is fully reclinedand the legrest isfully raised.Press and hold thebutton down to rotate theheadrest forward. Releasethe button to stop theheadrest in any positionor when fully forward.Press and hold the buttondown to increase thelumbar intensity. Releasethe button to stop thelumbar in any position orwhen fully extended.– To reduce the risk of serious injury:• Do not attempt to disassemble or service the pump or motor; no serviceable parts areinside. Contact your La-Z-Boy ®dealer for service.• Check the condition of the power supplies, electrical cords, plugs, and connectors often.Keep the power supplies and electrical cords away from heat sources. Never operatethe unit with a damaged power supply, electrical cord, plug or connector. Contact yourLa-Z-Boy ®dealer for service.• The PowerReclineXR ® + and PowerReclineXRw + TM units are intended for a single occupant notexceeding 300 pounds per seat. Do not operate an individual seat with more than oneoccupant in or on any part of the individual seat.WARNINGPowerReclineXR®+ & PowerReclineXRw+TMOperating InstructionsTroubleshooting for Legrest OperationIf the legrest stops moving while closing, it may have encountered an obstruction.1. Check to make sure there are no obstructions. Lift and hold the legrest up, look for obstructionsand remove them.2. The legrest uses spring tension to close, and will close quickly when the obstruction is removed.Release the legrest slowly to prevent it from slamming shut.Troubleshooting for PowerReclineXR ®+ and PowerReclineXRw+TM Operation1. Make sure the 120 volt power cord is plugged into an electrical outlet.2. Check the power supply to make sure the green LED power indicator light is on.3. Make sure the electrical outlet is working. For example, make sure there are no blownfuses or tripped circuit breakers.4. Make sure all the connectors are secure; refer to the Assembly Instructions.5. Make sure the electrical cords are not crimped or pinched. Make sure the electric cordor plug is not damaged.6. Make sure the operating capacity has not been exceeded and there is only one occupantin the individual seat or unit; refer to the Operating Instructions.Power Supply ReplacementIf the power supply must be replaced:1. Unplug the power supply from the electrical outlet.2. Unplug the 120 volt power cord from the electrical outlet and disconnect the power supply fromeither the Y-cable or motor connector, whichever comes with the product.3. Connect the new power supply to the motor connector or (Y-cable), and close the locking coverwhen applicable. Connect the 120 volt power cord to the new power supply; refer to theAssembly Instructions.4. Proceed to the Battery Backup Assembly Instructions.If the unit still does not operate properly, contact your dealer for instructions on returning the unitfor examination and repair. Except for the replacement of the power supply, never attempt to makeany repairs or adjustments yourself.