La Crosse Technology WS6812 Quick Setup Manual

La Crosse Technology WS6812 Quick Setup Manual Manual pdf 1 page image

Wireless Weather StationWS6812 | Quick Setup GuideThe Wireless Weather Station features manual set time, date, time alarm,Outdoor/Indoor temperature alerts, and moon phase. Monitor temperatureand humidity, track temperature trends and set customizable temperaturealerts--all in one convenient device. Wireless transmission range of over300 feet (90 meters) in open air, from transmitter to weather station.SETUP INSTRUCTIONS STEP BY STEPSTEP 1: Remove battery cover from the weather station. Slide tab down and pullout to remove the battery cover. Insert 2 NEW AA batteries (not included) into the backof the weather station. Observe the correct polarity(see marking inside the battery compartment).The weather station will light up and show,indoor temperature, humidity and time. Do Not Mix Old and New Batteries Do Not Mix Alkaline, Standard, Lithium or Rechargeable BatteriesSTEP 2: Ensure that the transmitter is within 10 feet of the Weather Station. To remove battery cover from transmitter, slide the batterycover down and lift off the front of the transmitter. Insert 2 NEW AA batteries (not included) into the transmitter. Observe the correct polarity. Within 3 minutes the weather station will show readings in theoutdoor temperature area on the LCD. Note: Allow the weather station and the transmitter to staywithin 10 feet of each other for the first 15 minutes of set up.TRANSMITTER SIGNAL STRENGTH After the batteries are inserted, the weather station will search for theoutdoor temperature/humidity transmitter for 3 minutes. The antenna symbol will flash during reception, and temperaturedisplay will be dashes “---“. The antenna symbol will scroll during signal synchronization. If synchronization fails once, the antenna will lose one bar. If synchronization fails twice, the antenna will lose two bars. If reception continuously fails to receive 5 times, the antenna symbol willbe shown as . The antenna will show full display with successful RF (radiofrequency) reception.TROUBLESHOOTING If the outdoor data are not displayed after three minutes,hold the SENSOR button on the weather station for threeseconds to search for outdoor transmitter. Next, press the TX button on the outdoor transmitter to send signal. If it still does not receive the outdoor data, remove batteries from boththe weather station and the transmitter for 15 minutes then repeat thesetup instructions from step 1. The maximum transmitting range in open air is over 300-feet (90meters). Obstacles such as walls, windows, stucco, concrete, and largemetal objects can reduce the range.TIME/DATEThe TIME/DATE button will move through the programmenu and confirm settings.Use the UP ARROW button to increase a value.Use the DOWN ARROW button to decrease a value.SET TIME AND DATEHold the TIME/DATE button for three seconds to enter time set mode. YEAR: The Year will flash. Use the ARROW buttons to choose the year,and press the TIME/DATE button to confirm and move to the month. MONTH: The Month will flash, use the ARROW buttons to choose themonth, and press the TIME/DATE button to confirm and move to thedate. DATE: The Date will flash. Use the ARROW buttons to choose the date,and press the TIME/DATE button to confirm and move to 12/24 hourtime format. 12/24-HOUR: The time format will flash. Use the ARROW buttons tochoose 12-hour or 24-hour time format and press the TIME/DATE buttonto confirm and move to language. LANGUAGE : The language will flash. Use the ARROW buttons to selectthe language for weekday display (French, Italian, Dutch, Spanish,Danish, English or German - refer to the table hereunder) and press theTIME/DATE button to confirm and move to hour. HOUR: The Hour will flash. Use the ARROW buttons to choose thehour, and press the TIME/DATE button to confirm and move to minutes. MINUTES: The Minutes will flash. Use the ARROW buttons to choosethe minutes, and press the TIME/DATE button to confirm and move toFahrenheit/Celsius. FAHRENHEIT/CELSIUS: °F or °C will flash. Use the ARROW buttonsbutton to select Fahrenheit or Celsius. Press and release theTIME/DATE button to confirm and exit the program menu.Note: When no buttons are pressed for ten seconds, the weather stationwill save the last change and default back to normal time andtemperature display mode.TIME ALARMThe TIME ALARM button moves through the alarm settingmode and confirms the final setting.Use the UP ARROW button to increase a value.Use the DOWN ARROW button to decrease a value.SET TIME ALARMFrom normal time and temperature display mode, press and release theTIME ALARM button once to show alarm time. Hold the TIME ALARMbutton for three seconds to enter alarm set mode. HOUR: The Hour will flash. Use the ARROW buttons to set the hour,and press TIME ALARM button to confirm and switch to minutes. MINUTES: The Minutes will flash. Use the ARROW buttons to set theminutes, and press TIME ALARM button to confirm. Press the TIME/DATE button to return to normal mode

/ 3

Related manuals for La Crosse Technology WS6812