LaCie 12big rack serial Installing the I/O Modules/Connecting StorageQuick Install Guide page 7Figure 11: Installing the I/O Module (2)Connecting Storage9.System to HostFigure 12: Basic ConfigurationFigure 13: Single Host, Single ConnectionFigure 14: Dual Host, Single ConnectionFigure 15: Dual Host, Dual ConnectionimPortant: Refer to release note for configuration ofmaximum number of enclosures.

Introduction

Preparation

Mounting the System into the Rack

Installing Modules

Installing the Dual Fan Cooling Module

Installing the I/O Modules

Installing Drives

I/O Module

LaCie 12big Rack Serial Quick Install Manual

shared folders

contacting customer support

12big Rack Fibre 8

ESD Precautions

Replacing a Fan

Battery Safety

Start up and login

Mount the array

Share the volume

distributed file system

safety guidelines

System Overview

The Enclosure Core Product

LaCie 12big Rack Network System Configurations

ATX Server Subsystem

ATX Server I/O Panel Connectors

Operator's (Ops) Panel

Power Supply Unit

Power Supply Output Loom

Drive Carrier Module

Blanking Plates

Installation

Enclosure Installation Pre-Requisites

Special Tools and Equipment

Chassis Installation

Grounding Checks

Operation

Ops Panel LEDs and Switches

Starting the Drives

Power Down

Overview

LED States

Cooling Fan LEDs

ATX Server LEDs

Audible Alarm

Troubleshooting

Thermal Monitoring and Control

Drive Carrier Module Faults

Module Replacement

Power Supply Units

Installing a Power Supply Unit

Cooling Fans

Installing a Cooling Fan

Installing a Drive Carrier

Replacing the SAS Expander PCB

Replacing ATX Motherboards

Replacing PCI Cards

Replacing the Boot Drives

Technical Specifications

AC Power Module (2 x 850W PSU)

Cooling Fan

International Standards

EMC Compliance

Rack Kit Reference Drawing

Contacting Customer Support

Warranty Information

box content

Unpacking

Fitting Modules

Operator Panel

Managing your RAID

Create a RAID-Protected Disk Array

Mount the Array

Safety Guidelines

Battery Precautions

Rack System Safety Precautions

Enclosure Chassis

PCI Express Slots

Enclosure Rear Panel

Rack Installation Pre-Requisites

Equipment

Installing the Modules

Power Supply Unit LEDs

Drive Carrier LEDs

Network Port LEDs

The Management GUI

Sensor

Control

Users

BIOS Settings

Menu Bar

Main Menu

ACPI Configuration Sub-Menu

Chipset ACPI Configuration Sub-Menu

South Bridge Configuration Sub-Menu

Processor Power Management Configuration Sub-Menu

Drive Configuration Sub-Menu

AHCI Configuration Sub-Menu

IDE Configuration Sub-Menu

Event Log Configuration Sub-Menu

PCI Slots Configuration Sub-Menu

SuperIO Configuration Sub-Menu

USB Configuration Sub-Menu

Virtualization Configuration Sub-Menu

Boot Menu

Boot Settings Configuration Sub-Menu

Boot Device Priority Sub-Menu

Other Drives Sub-Menu

IP Address Sub-Menu

Subnet Mask Sub-Menu

IPMI Device and Firmware Information Sub-Menu

Exit Menu

Console Redirection (VT100 Mode)

Troubleshooting and Problem Solving

LED/Audible Alarm Interpretation

Module Removal and Replacement

Removing a Drive Carrier

Replacing Components on the ATX Motherboard

Replacing Memory Modules

Gem Enclosure Firmware

Upgrading the Firmware

big Rack Storage Server Upgrade Procedure

Upgrade Filenames

Version Checking

AC Power Cords

POST Code Checkpoints

DIM Code Checkpoints

Memory Initialization Error Codes

IPMI Command List

Storage Commands

Transport Commands

Glossary

Battery Disposal

Installation Preparation

Disk Slot Arrangement

Connecting the Storage System to the Host

Connecting the Power Cords

completing the installation

Setting up the Embedded StorView Module: Mac OS

system requirements

data security

big Rack Fibre Expansion Enclosure

Bay Identification

Visible Alarms - OPS LEDs

The Plug-in Modules

LaCie 12big Rack Fibre 8 RAID Controller Module

Battery Module

StoreView Management Software

Blank I/O Modules

Drive Status Indicators

MUX Transition Cards

Getting Started

Enclosure Drive Slot Number Convention

Enclosure Installation Procedures

Rack Installation Procedure

Rack Mounting Rail Kit

Module Removal & Installation

Installing the Power Cooling Module

Installing a Drive Carrier Module

Engaging the Anti-tamper Locks

RAID Controller Module

Installing the RAID Controller Module

Installing the Disk I/O Module

SFP Transceiver Installation

Cabling the Enclosures

Cabling Multiple Enclosures

Ethernet Connection

OPS Panel LEDs

Starting StorView

Setting Up the Embedded StorView Module: Microsoft Windows

Setting up the Embedded StorView Module: Linux

troubleshooting

Status Indicators (LEDs)

RAID Controller Module LEDs

Disk I/O Module LEDs

drive carrier leds

Symptoms and Solutions

Power Cooling Module Faults

Thermal Alarm

Firmware Updates

dealing with hardware faults

Replacing the Power Cooling Module (PCM)

Replacing the RAID Controller Module

Disk I/O Module

Removal and Installation of the Blank I/O Module

Removing the Battery Module

Removing the SFP Transceiver

Dummy Drive Carrier Module Replacement

Appendix A: Technical Specifications

Enclosure Environment

LaCie 12big Rack Fibre 8 RAID Controller Module Specification

Drive Carrier Module Specification

Appendix B: Standards & Regulations

Potential for Radio Frequency Interference

European Regulations

EMC Precautions

minimum system requirements

Cables

Operator's Panel

Audible Alarms