Magnavox 55MV314X Owner's Manual

Also see for 32MV304X: Owner's manual Owner's manual

Contents

Magnavox 55MV314X Owner's Manual Manual pdf 15 page image

6 TroubleshootingIf the Unit does Not Perform Properly when Operated as Instructed in this Manual,check the following Troubleshooting Tips and All Connections Once before calling for Service.PowerNo Power● Make sure that the AC outlet supplies the proper voltage, pluganother electrical appliance into the AC outlet to ensure that the ACoutlet operates normally.● If a Power Failure occurs, Unplug the AC Power Cord for 1 minuteto allow the Unit to Reset Itself.RemoteRemote Control Buttons or Remote itself does Not Work.● Re-insert the Batteries with their Polarities (+/–) as indicated.● When there is an Infrared-equipped device near this Unit, it mayinterrupt the Remote Control Signal from this Unit.● Make sure that Nothing is Blocking the Unit's Remote ControlSensor and the Remote Control is Pointed at this Remote ControlSensor.● Press and Hold any Key on Remote Control toward a Digital or CellPhone Camera. The Remote Control is working if you confirm aFlashing Infrared Light through the Camera. Some Dual Camera CellPhones may have an IR Filter in one of the Cameras.Universal Remote Control does not work properly.● Refer to the Owner's Manual for the Universal Remote Control toobtain the MAGNAVOX code.PicturePower is On but No Screen Image.● Check whether the Connection for the Antenna, Cable or SatelliteSet-top Box is Connected Correctly.● Check whether All the Cables to the Unit are connected to the correctOutput Jack on your separate Device like Blu-ray Disc / DVD Recorder.● Check if your computer is NOT in Sleep Mode when the Input Modeon this Unit is in PC mode. Tap any Key on the Computer Keyboardto Wake it up.● Check if the correct Input Mode is selected by pressing SOURCE.No Color● Adjust Color in Picture settings. L p. 10Picture Poor, Sound OK● Electrical Interference from nearby appliances may affect Picture Quality.● Adjust Contrast and Brightness in Picture Settings. L p. 10● For the Best Picture Quality, watch “High Definition” wide screenPrograms. If the HD content is Not available, watch “StandardDefinition” Programs instead.You see Noise or Trash on the Screen.● When the capabilities on the Unit exceed the capabilities of theDigital Broadcasting, the signal will be increased to match thecapabilities of the Display on the Unit. This may cause Noise or Trash.Unusual picture appears and the TV does Not Operate.● Press the Power button first. If it does not solve, follow the procedurebelow.Press the buttons on the Remote Control in the order shown below.KLHLILBUnplug the AC Power Cord once, and wait for 1 minute, andthen plug it in again.Picture & SoundNo Picture or Sound● View other TV channels. The problem might be limited to theBroadcasting Station or Weak Signal Strength.● Unplug the AC Power Cord and wait for about 1 minute, then Plugthe AC Power Cord and turn On the Unit again.● Autoprogram must be completed when you Set Up the Unit for theFirst time or Move it to a location where previously unavailablechannels are broadcast.● The selected Channel cannot be viewed by the Child and RatingsLock Setting. L p. 13● The Unit requires some kind of Input Signal. A Digital Indoor Antenna(VHF / UHF), a Digital External Antenna (VHF / UHF) or an RFcoaxial cable from your Wall or Cable/Satellite Set-top Box signal(HDMI, Component+Audio or Composite [Video+Audio]) needsto be connected to the Unit.Adjusted Picture or Sound settings are not effective every time theUnit is turned On.● You must set to Home in Location. L p. 13 (Otherwise, theSettings you adjusted will not be memorized after the Unit goes intoStandby Mode.)You see a Distorted Picture or Hear an Unusual Sound.● You may be getting NTSC (Analog) TV signal (not HDTV signal)interference from electrical appliances, automobiles, motorcycles orfluorescent lights.● Try moving the Unit to another Location to see if this is the Causeof the Problem.SoundNo Sound, Distorted Sound or Incorrect Audio Sound is heard whenusing the HDMI-DVI connections.● Make sure that the Analog Audio signals from the HDMI-DVI deviceare connected to the Analog Audio Input L/R jacks.Sound Poor, Picture OK● Check if the Audio Cable is connected into the Unit correctly.You Switch to a Different Input and the Volume Changes.● This Unit will Memorize the Volume Level from the last time youadjusted it.● If the Volume of the Sound from another Device is Higher or Lower,then the Loudness will Change.Child and Rating LockForgotten PIN code.● Enter “0711” to clear your password.ScreenYou Switch to a different Input and the Screen Size changes.● This Unit will Memorize the Viewing Mode from the last time youused those Particular Input Modes.The Display image does not cover the Entire Screen.● If you are using the unit as a PC monitor, make sure that Horizontalposition and Vertical position in PC settings are set correctly.● If you are watching TV or using the Composite Video, ComponentVideo or HDMI with 480i Input, press PICTURE SIZEARepeatedly to Switch to various Screen Modes.Closed CaptionsClosed Captions are displayed as a white box. No Closed Captionsare displayed in the Closed Captions-Supported Program.● Interference from buildings or weather conditions may cause ClosedCaptions to be incomplete if watching Analog TV signals.● Broadcasting Station may shorten the program to insertadvertisements.● The Closed Captions Decoder cannot read the information of ashortened program.● Closed Captions that are delayed a few seconds behind the actualdialog are common for Live broadcasts. Most captioning productioncompanies can display a dialog to maximum of 220 words per minute.If a dialog exceeds that rate, selective editing is used to insure that theClosed Captions remain up-to date with the current TV screen dialog.Black Box is displayed on the TV Screen.● The Text mode is selected. For Closed Captions, select CC-1, CC-2,CC-3 or CC-4.NetworkCannot connect to the Network.● Check if the Ethernet cable connection is properly made. Turn Onthe modem or broadband router.● Check the Network settings.● Check if the broadband router and/or modem is correctlyconnected.O Note(s)● The LCD screen is manufactured to provide many years of usefullife. Occasionally a few non active pixels may appear as a fixed pointof blue, green or red.This is Not to be considered a Defect in the LCD screen.● Some Functions are not available in Specific Modes, but this is Nota Malfunction. Read the Description in this Manual for more Detailson Correct Operations.15English