Contents - contact information
- important safety instructions
- Table Of Contents
- Table Of Contents
- Introduction
- Features and Benefi ts
- Figure 1-1, Power Switch, Status LED, and Accessory Connection Ports
- Figure 1-3, Left Side Features
- How an Inverter/Charger Works
- Table 1-1, Typical Appliance Power Consumption
- Installation
- Figure 2-1, Simplifi ed Installation Diagram for Permanent Installations
- Figure 2-2, Approved Mounting Positions
- Figure 2-3, ME Series Dimensions and Side Reference
- Wiring the Inverter - General Requirements
- DC Wiring
- Figure 2-4, DC and Battery Temperature Sensor Wiring
- Table 2-1, Recommended DC Wire/Overcurrent Device for Rated Use
- Figure 2-5, Battery Hardware Installation
- Figure 2-7, Battery Temperature Sensor
- Figure 2-8, ME Series Inverter/Charger - AC Wiring
- Figure 2-10, AC Terminal Block
- Figure 2-11, AC Wiring for Single In - Single Out (30 A) Confi gurations
- Figure 2-12, AC Wiring for Single In - Single Out (60 A) Confi gurations
- Figure 2-13, AC Wiring for Single In - Dual Out Confi gurations
- Figure 2-14, AC Wiring for Dual In - Single Out Confi gurations
- Figure 2-15, AC Wiring for Dual In - Dual Out Confi gurations
- Table 2-4, AC Input/Output Wiring Confi gurations (ME2000 models)
- Figure 2-17, AC Wiring for Single In - Dual Out (ME2000-15B/-20B models) Confi gurations
- Table 2-5, Equipment Grounding Conductor Sizing
- Figure 2-18, Neutral-to-Ground Connection (Inverter Mode)
- Figure 2-20, Large Ground Wire Connected to ME Series
- Functional Test
- Figure 2-22, AC Voltage Checks
- Operation
- Standby Mode
- Figure 3-3, Automatic 4-Stage Charging Graph
- Battery Temperature Sensor Operation
- Table 3-1, Inverter Battery Turn On/Off Levels
- Figure 3-5, Power Switch and Status Indicator
- Table 3-2, Inverter/Charger Default Values
- Maintenance and Troubleshooting
- Troubleshooting
- Resetting the Inverter
- Appendix A - Specifi cations and Optional Equipment
- A-2 Optional Equipment and Accessories
- Appendix B - Battery Information
- B-5 Battery Bank Sizing Worksheet
- B-6 Battery Wiring Confi gurations
- Figure B-4, Battery Bank Wiring Examples (12-volt)
- Limited Warranty
|
Page 28© 2010 Magnum Energy, Inc.Installation2 4 0V A C onlyin s ta ndbyM a in P a n e l(S h o re P o w e r/G e n e ra to r In p u t)M E S e rie s In v e rte rA C T e rm in a l B lo c k( A C in p u t a n d o u tp u t w irin g )D U A L IN / D U A L O U T w irin gA C H O T 1 IN( from M a in P a nel)A C H OT 1 OU T(to S ub-P a nel)A C N E U T IN( from M a in P a nel)A C N EU T O U T(to S ub-P a nel)A C H O T 2 IN( from M a in P a nel)A C H OT 2 OU T(to S ub-P a nel)S u b-P a n e l a n d O u tle ts(In v e rte r L o a d s )1 2 0V A C 1 2 0V A CA C G R O U N D S(to /from bothP a ne ls)ONOFFO NO FFO NO F FO NO F FO NO FFO NO FFO NO F FO NO F FO NO FFO NO FFO NO F FO NO FFO NO F F3 0M axim um30 am p breaker(double pole)required toinverter AC input3 0In m obile installations : neutral is typically notconnected to ground in the m ain panel.O NO FFO NO FFO NO F FO NO FFONOFFFigure 2-15, AC Wiring for Dual In - Dual Out Configurations
|
