Makita 6402 Instruction Manual

Also see for 6402: Instruction manual Instruction manual Parts Breakdown Instruction manual Instruction manual

Contents

48. When operating a power tool outdoors, use anextension cord suitable for outdoor use. Use of acord suitable for outdoor use reduces the risk ofelectric shock.9. If operating a power tool in a damp location isunavoidable, use a residual current device (RCD)protected supply. Use of an RCD reduces the risk ofelectric shock.10. Use of power supply via a RCD with a ratedresidual current of 30 mA or less is alwaysrecommended.Personal safety11. Stay alert, watch what you are doing and usecommon sense when operating a power tool. Donot use a power tool while you are tired or underthe influence of drugs, alcohol or medication. Amoment of inattention while operating power toolsmay result in serious personal injury.12. Use personal protective equipment. Always weareye protection. Protective equipment such as dustmask, non-skid safety shoes, hard hat, or hearingprotection used for appropriate conditions will reducepersonal injuries.13. Prevent unintentional starting. Ensure the switchis in the off-position before connecting to powersource and/or battery pack, picking up or carryingthe tool. Carrying power tools with your finger on theswitch or energising power tools that have the switchon invites accidents.14. Remove any adjusting key or wrench beforeturning the power tool on. A wrench or a key leftattached to a rotating part of the power tool may resultin personal injury.15. Do not overreach. Keep proper footing andbalance at all times. This enables better control ofthe power tool in unexpected situations.16. Dress properly. Do not wear loose clothing orjewellery. Keep your hair, clothing, and glovesaway from moving parts. Loose clothes, jewellery orlong hair can be caught in moving parts.17. If devices are provided for the connection of dustextraction and collection facilities, ensure theseare connected and properly used. Use of dustcollection can reduce dust-related hazards.Power tool use and care18. Do not force the power tool. Use the correct powertool for your application. The correct power tool willdo the job better and safer at the rate for which it wasdesigned.19. Do not use the power tool if the switch does notturn it on and off. Any power tool that cannot becontrolled with the switch is dangerous and must berepaired.20. Disconnect the plug from the power source and/orthe battery pack from the power tool beforemaking any adjustments, changing accessories,or storing power tools. Such preventive safetymeasures reduce the risk of starting the power toolaccidentally.21. Store idle power tools out of the reach of childrenand do not allow persons unfamiliar with thepower tool or these instructions to operate thepower tool. Power tools are dangerous in the handsof untrained users.22. Maintain power tools. Check for misalignment orbinding of moving parts, breakage of parts andany other condition that may affect the powertool’s operation. If damaged, have the power toolrepaired before use. Many accidents are caused bypoorly maintained power tools.23. Keep cutting tools sharp and clean. Properlymaintained cutting tools with sharp cutting edges areless likely to bind and are easier to control.24. Use the power tool, accessories and tool bits etc.in accordance with these instructions, taking intoaccount the working conditions and the work tobe performed. Use of the power tool for operationsdifferent from those intended could result in ahazardous situation.Service25. Have your power tool serviced by a qualifiedrepair person using only identical replacementparts. This will ensure that the safety of the power toolis maintained.26. Follow instruction for lubricating and changingaccessories.27. Keep handles dry, clean and free from oil andgrease.GEB001-6DRILL SAFETY WARNINGS1. Use auxiliary handle(s), if supplied with the tool.Loss of control can cause personal injury.2. Hold power tool by insulated gripping surfaces,when performing an operation where the cuttingaccessory may contact hidden wiring or its owncord. Cutting accessory contacting a “live” wire maymake exposed metal parts of the power tool “live” andcould give the operator an electric shock.3. Always be sure you have a firm footing.Be sure no one is below when using the tool inhigh locations.4. Hold the tool firmly.5. Keep hands away from rotating parts.6. Do not leave the tool running. Operate the toolonly when hand-held.7. Do not touch the drill bit or the workpieceimmediately after operation; they may beextremely hot and could burn your skin.8. Some material contains chemicals which may betoxic. Take caution to prevent dust inhalation andskin contact. Follow material supplier safety data.SAVE THESE INSTRUCTIONS.WARNING:DO NOT let comfort or familiarity with product (gainedfrom repeated use) replace strict adherence to safetyrules for the subject product. MISUSE or failure tofollow the safety rules stated in this instructionmanual may cause serious personal injury.