Makita AN634H Instruction Manual

Also see for AN635H: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

Contents

Makita AN634H Instruction Manual Manual pdf 12 page image

12 ENGLISHSingle sequential actuationPlace the contact element against the workpiece andSXOOWKHWULJJHUIXOO\$IWHUQDLOLQJUHOHDVHWKHFRQWDFWHOHPHQWDQGWKHQrelease the trigger.ŹFig.24CAUTION: Do not place the contact elementagainst the workpiece with excessive force. Also,pull the trigger fully and hold it on for 1-2 secondsafter nailing.(YHQLQWKH³6LQJOHVHTXHQWLDODFWXDWLRQ´PRGHKDOISXOOHGWULJJHUFDXVHVDQXQH[SHFWHGQDLOLQJZKHQWKHcontact element re-contacts the workpiece.Contact actuation3XOOWKHWULJJHU¿UVWDQGWKHQSODFHWKHFRQWDFWHOHPHQWagainst the workpiece.ŹFig.25Nailing on steel plateWARNING: When nailing on the C-shapedVWHHOOLPLWWKHWKLFNQHVVWRPP Ǝ RUthinner. Otherwise the tool will bounce severely andDQDLOVWUXFNEDFNFDXVLQJVHULRXVLQMXULHVWARNING: Use hardened nails only for steelplate. Using other purposed nails may cause seriousLQMXULHVWARNING: When nailing, hold the tool so thatit stands upright to the driving surface. SlantedQDLOLQJPD\FDXVHQDLOVWRVWULNHEDFNFDXVLQJVHUL-RXVLQMXULHVWARNING: Do not use the tool for fasteninga corrugated plate or the C-shaped steel directly.,WPD\FDXVHQDLOVWRVWULNHEDFNFDXVLQJVHULRXVLQMXULHVWARNING: Do not use the tool for nailing onceiling or roof.&KRRVHDQGXVHQDLOVPP Ǝ RUPXFKORQJHUWKDQWRWDOWKLFNQHVVRIDOOZRUNSLHFHWREHIDVWHQHG5HIHUWRthe table below.Material thick-ness includingC-shaped steel (A)C-shaped steel (B)thicknessNail length (C)9 mm - 22 mmƎƎ1.6 mm - 2.3 mmƎƎPP Ǝ10 mm - 27 mmƎƎPP Ǝ14 mm - 35 mmƎƎPP Ǝ15 mm - 40 mmƎƎPP ƎŹFig.26NOTICE: Depending on the hardness andtotal thickness of all workpiece in combination,enough fastening may not be obtained. Nailing onsteel plate with excessive depth may extremelyreduce the fastening force.%HIRUHQDLOLQJDGMXVWthe nailing depth properly.NOTICE: Nailing on the steel plate makes thedriver prematurely worn out and it may cause nailjamming.:KHQWKHGULYHULVZRUQUHSODFHLWZLWKDnew one.Nailing on concreteWARNING: Use hardened nails only for con-crete. Using other purposed nails may cause seriousLQMXULHVWARNING: Do not nail directly on the con-crete or do not fasten directly the steel plate tothe concrete.,WPD\FDXVHFRQFUHWHIUDJPHQWVWRÀ\RIIRUQDLOVWRVWULNHEDFNFDXVLQJVHULRXVLQMXULHVWARNING: When nailing, hold the tool so thatit stands upright to the driving surface. SlantedQDLOLQJPD\FDXVHFRQFUHWHIUDJPHQWVWRÀ\RIIRUQDLOVWRVWULNHEDFNFDXVLQJVHULRXVLQMXULHVWARNING: Do not use the tool for fasteningan object to hang something such as sewer pipe.&KRRVHDQGXVHQDLOVVRWKDWWKHSHQHWUDWLRQGHSWKLQWRFRQFUHWHUDQJHVPP Ǝ PP Ǝ 5HIHUWRthe table below.Wood thick-ness (A)Nail length (B) Penetration depthinto concrete (C)PP Ǝ PP Ǝ Approx. 12 mmƎPP Ǝ PP Ǝ Approx. 13 mmƎPP Ǝ PPPPƎƎ$SSUR[PPPP ƎƎPP Ǝ PP Ǝ Approx. 15 mmƎPP Ǝ PP Ǝ Approx. 12 mmƎPP Ǝ PP Ǝ Approx. 15 mmƎŹFig.27NOTICE: Use the tool only for soft concretebuilt up not so long before. Driving nails into hardFRQFUHWHPD\FDXVHQDLOEHQGLQJRUQDLOLQJLQWRLQVXI-¿FLHQWGHSWKNOTICE: When penetrating into concreteGHHSHUWKDQPP Ǝ QDLOVPD\QRWEHGULYHQVXI¿FLHQWO\Cutting linked sheetCAUTION: Always disconnect the air hosefrom the tool before removing the linked sheet.